LT1195 LINER [Linear Technology], LT1195 Datasheet
LT1195
Available stocks
Related parts for LT1195
LT1195 Summary of contents
Page 1
... The LT1195 is a low power version of the popular LT1190, and is available in 8-pin miniDIPs and SO packages with standard pinouts. The normally unused pin 5 is used for a shutdown feature that shuts off the output and reduces power dissipation to a mere 15mW ...
Page 2
... Differential Input Voltage ......................................... 6V Input Voltage ........................................................... V Output Short-Circuit Duration (Note 1) ......... Continuous Operating Temperature Range LT1195M ........................................ – 125 C LT1195C ................................................ Junction Temperature (Note 2) Plastic Package (CN8, CS8) ............................ 150 C Ceramic Package (CJ8, MJ8) .......................... 175 C Storage Temperature Range ................. – 150 C Lead Temperature (Soldering, 10 sec).................. 300 C – ...
Page 3
... LT1195M/C MIN TYP MAX UNITS 0.8 1 160 ns 700 ns LT1195M/C MIN TYP MAX UNITS 3.0 9.0 mV 3.0 11.0 mV 0.2 1.0 A 0.5 2.0 A 2.0 3 0.5 3.0 V/mV 3.5 3.8 V 0.25 0.4 V 140 MHz 0.8 1 LT1195M MIN TYP MAX UNITS 3.0 15 0.2 2.0 A 0.5 2 1.50 5.0 V/mV 0.25 0.8 V/mV 3.7 3 0.8 2 ...
Page 4
... Shutdown Pin Current S/D Note 1: A heat sink may be required to keep the junction temperature below absolute maximum when the output is shorted continuously. Note calculated from the ambient temperature T J dissipation P according to the following formats LT1195MJ8, LT1195CJ8 LT1195N ...
Page 5
... VOLTAGE (V) 1195 G05 Open-Loop Gain vs Temperature 10k V = ± ± 150 –50 – TEMPERATURE (°C) 1195 G08 LT1195 75 100 125 1195 G03 –55°C 25°C 125° 1195 G06 75 100 125 1195 G09 5 ...
Page 6
... LT1195 W U TYPICAL PERFOR A Gain and Phase vs Frequency 100 PHASE GAIN ± 25° –20 100k 1M 10M 100M FREQUENCY (Hz) 1195 G10 Unity-Gain Frequency and Phase Margin vs Temperature 100 V = ±5V S UNITY-GAIN FREQUENCY 80 UNITY-GAIN PHASE MARGIN ...
Page 7
... SETTLING TIME (ns) 1195 G20 Large-Signal Transient Response A = – LT1195 4 2 – INPUT OFFSET VOLTAGE CAN BE ADJUSTED OVER A ±150mV RANGE WITH 10k POTENTIOMETER. LT1195 1mV 1mV 400 300 1195 G21 1195 G23 1195 G25 7 ...
Page 8
... Using the Shutdown Feature into P-P The LT1195 has a unique feature that allows the amplifier to be shut down for conserving power, or for multiplexing several amplifiers onto a common cable. The amplifier will shutdown by taking pin dissipates 15mW while maintaining a true high impedance output state of 15k in parallel with the feedback resistors ...
Page 9
... The maximum output slew rate in the photo is 30V/ s. This rate is set by the 30mA current limit driving 1000pF. Operation on Single 5V Supply The LT1195 has been optimized for a single 5V supply. This circuit amplifies standard composite video (1V including sync and drives a double-terminated 75 cable. Resistors R1 and R2 bias the amplifier at 2V, allowing the sync pulses to stay within the common-mode range of the amplifier ...
Page 10
... A bidirectional “video bus” consists of the LT1195 op amp and the LT1187 video difference amplifier. A pair of LT1195s at TRANSMIT 1, is used to generate differential signals to drive the line which is back-termi- nated in its characteristic impedance. The LT1187, twisted-pair receiver, converts signals from differential to single-ended ...
Page 11
... 300 V V BIAS BIAS BAL TRANSMIT LT1195 – – 6 LT1195 S – LT1187 – 300 R G 300 RECEIVE 1 1195 AI12 1195 SS LT1195 + V V OUT – ...
Page 12
... LT1195 PACKAGE DESCRIPTIO CORNER LEADS OPTION 0.023 – 0.045 0.290 – 0.320 (0.58 – 1.14) HALF LEAD (7.366 – 8.128) OPTION 0.045 – 0.065 (1.14 – 1.65) FULL LEAD OPTION 0.008 – 0.018 0° – 15° (0.203 – 0.460) 0.045 – 0.065 0.385 ± 0.025 (1.14 – ...