MAX4027 Maxim, MAX4027 Datasheet
MAX4027
Available stocks
Related parts for MAX4027
MAX4027 Summary of contents
Page 1
... The device has low (0.012%/0.014°) differential gain and phase errors, and operates from ±5V supplies. The MAX4027 is ideal for use in broadcast and graph- ics video systems because of the low 2pF input capaci- tance, channel-to-channel switching time of only 15ns, and wide 62MHz, large-signal 0 ...
Page 2
... Note 1: Continuous power-dissipation rating must also be observed. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
AC ELECTRICAL CHARACTERISTICS ( -5V 0V 75Ω to GND IN_ _ IN PARAMETER SYMBOL AMPLIFIER CHARACTERISTICS Small-Signal -3dB Bandwidth Small-Signal Bandwidth for BW ±0.1dB Gain Flatness Large-Signal -3dB Bandwidth ...
Page 4
Triple, 2-Channel Video Multiplexer-Amplifier (V = +5V -5V 150Ω to GND SMALL-SIGNAL FREQUENCY RESPONSE 20mV IN_ _ P +2V ...
Page 5
... TOTAL HARMONIC DISTORTION vs. FREQUENCY - OUT_ P-P -30 -40 -50 -60 -70 -80 - 10M FREQUENCY (Hz) LARGE-SIGNAL PULSE RESPONSE (C = 20pF) LOAD MAX4027 toc14 V IN_ _ 500mV/div 0V V OUT_ 1V/div 0V 10ns/div A/B SWITCHING TRANSIENT MAX4027 toc17 A/B 2.5V/div 0V V OUT_ 100mV/div 0V 20ns/div 100M MAX4027 toc15 0V 0V MAX4027 toc18 ...
Page 6
Triple, 2-Channel Video Multiplexer-Amplifier (V = +5V -5V 150Ω to GND SUPPLY CURRENT vs. TEMPERATURE -50 - ...
Page 7
... This VCL A Table 2. Output Control Logic Drive EN high to place the MAX4027 in disable mode. Placing the device in disable mode reduces the quies- cent current to 17mA (V the amplifier outputs into a high-impedance state, typi- Pin Description Truth Tables AMPLIFIER INPUT FUNCTION IN_A ...
Page 8
... The MAX4027 is enabled when EN is unconnected. Video Line Driver The MAX4027 is well suited to drive short coaxial trans- mission lines when the cable is terminated at both ends (Figure 1) where the fixed gain of +2 compensates for the loss in the back termination. Cable frequency response may cause variations in the flatness of the signal ...
Page 9
... Figure 2. Switching Timing Diagram _______________________________________________________________________________________ 225MHz, Triple, 2-Channel Video Multiplexer-Amplifier pins. IN1A IN1B IN2A IN2B t SW CHANNEL A IN3A IN3B t PDE TRANSISTOR COUNT: 870 PROCESS: Bipolar Functional Diagram V A MUX1 OUT1 TO A MUX2 OUT2 TO A MUX3 OUT3 MAX4027 GND V EE Chip Information 9 ...
Page 10
... Triple, 2-Channel Video Multiplexer-Amplifier (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages TOP VIEW FRONT VIEW 10 ______________________________________________________________________________________ SIDE VIEW Package Information ...
Page 11
... For the latest package outline information go to www.maxim-ic.com/packages.) Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...