MAX483 Maxim Integrated Products, MAX483 Datasheet
MAX483
Available stocks
Related parts for MAX483
MAX483 Summary of contents
Page 1
... These transceivers draw between 120µA and 500µA of supply current when unloaded or fully loaded with disabled drivers. Additionally, the MAX481, MAX483, and MAX487 have a low-current shutdown mode in which they consume only 0.1µA. All parts operate from a single 5V supply. ...
Page 2
Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers ABSOLUTE MAXIMUM RATINGS Supply Voltage (V ) .............................................................12V CC Control Input Voltage (RE, DE)...................-0. Driver Input Voltage (DI).............................-0. Driver Output Voltage (A, B)...................................-8V to +12.5V Receiver Input Voltage (A, B).................................-8V to +12.5V ...
Page 3
... Figures 5 and 11 15pF, S1 closed LZ RL Figures 5 and 11 15pF, S2 closed HZ RL MAX481 (Note 5) MIN TYP MAX 120 250 300 500 500 900 CC 300 500 300 500 CC 230 400 MAX483 350 650 MAX487 250 400 120 250 0 250 35 250 7 95 MIN TYP MAX ...
Page 4
... S1 closed RL Figures 5 and 11 15pF, S2 closed < 50% of data period PLH PHL MAX483/MAX487 (Note 5) MAX483/MAX487, Figures 7 and 100pF, S2 closed L MAX483/MAX487, Figures 7 and 100pF, S1 closed L MAX483/MAX487, Figures 5 and 11 15pF, S2 closed L MAX483/MAX487, Figures 5 and 11 15pF, S1 closed L MIN TYP MAX UNITS 40 100 ns 40 100 ns 300 ...
Page 5
... Note 4: Applies to peak current. See Typical Operating Characteristics. Note 5: The MAX481/MAX483/MAX487 are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts are guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown ...
Page 6
... DRIVER OUTPUT LOW VOLTAGE 140 120 100 OUTPUT LOW VOLTAGE (V) MAX483/MAX487–MAX489 SUPPLY CURRENT vs. TEMPERATURE 600 500 400 MAX483 300 MAX487 200 MAX483/MAX487 MAX488/MAX489 100 MAX483/MAX487 -50 -25 0 TEMPERATURE ( C) 6 _______________________________________________________________________________________ OUTPUT CURRENT vs. DRIVER OUTPUT HIGH VOLTAGE -120 -100 -80 -60 -40 - OUTPUT HIGH VOLTAGE (V) SUPPLY CURRENT vs ...
Page 7
... MAX481 7 GND MAX483 MAX485 MAX487 MAX1487 MAX Figure 1. MAX481/MAX483/MAX485/MAX487/MAX1487 Pin Configuration and Typical Operating Circuit _______________________________________________________________________________________ Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers NAME MAX489/ NAME MAX491 DIP/SO Receiver Output > 200mV, RO will be high < 200mV, RO will be low. Receiver Output Enable enabled when RE is low high impedance when RE is high. ...
Page 8
... MAX1487 are low-power transceivers for RS-485 and RS- 422 communications. The MAX481, MAX485, MAX490, MAX491, and MAX1487 can transmit and receive at data rates up to 2.5Mbps, while the MAX483, MAX487, MAX488, and MAX489 are specified for data rates up to 250kbps. The MAX488–MAX491 are full-duplex trans- ceivers while the MAX481, MAX483, MAX485, MAX487, and MAX1487 are half-duplex ...
Page 9
... B RE Figure 7. Driver Timing Test Load monics with large amplitudes are evident. Figure 13 shows the same information displayed for a MAX483, MAX487, MAX488, or MAX489 transmitting under the same conditions. Figure 13’s high-frequency harmonics have much lower amplitudes, and the potential for EMI is significantly reduced ...
Page 10
... Figure 9. Driver Enable and Disable Times (except MAX488 and MAX490 1. Figure 11. Receiver Enable and Disable Times (except MAX488 and MAX490) Table 2. Receiving OUTPUTS High High Don't care High-Z = High impedance * Shutdown mode for MAX481/MAX483/MAX487 1. ZL(SHDN) ZL 2.3V V +0.5V OUTPUT NORMALLY LOW OL OUTPUT NORMALLY HIGH V -0.5V 2. ZH(SHDN 1. ZL(SHDN ...
Page 11
... Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers 10dB/div 0Hz 5MHz Figure 13. Driver Output Waveform and FFT Plot of MAX483/ MAX487–MAX489 Transmitting a 150kHz Signal Excessive output current and power dissipation caused by faults or by bus contention are prevented by two mechanisms. A foldback current limit on the output stage provides immediate protection against short cir- cuits over the whole common-mode voltage range (see Typical Operating Characteristics) ...
Page 12
... Figure 15. MAX481/MAX485/MAX490/MAX491/MAX1487 Receiver t PHL A 500mV/div B RO 2V/div 400ns/div Figure 17. MAX483, MAX487–MAX489 Receiver t 12 ______________________________________________________________________________________ 100pF Z B TTL < 6ns 100pF 500mV/div A 2V/div RO Figure 16. MAX481/MAX485/MAX490/MAX491/MAX1487 Receiver t PLH B 500mV/div + 2V/div RO Figure 18. MAX483, MAX487–MAX489 Receiver t PHL RECEIVER OUT + 20ns/div + 400ns/div PLH ...
Page 13
... RO RE MAX481 MAX483 MAX485 MAX487 MAX1487 Figure 21. MAX481/MAX483/MAX485/MAX487/MAX1487 Typical Half-Duplex RS-485 Network ______________________________________________________________________________________ Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers Figures 21 and 22 show typical network applications circuits. These parts can also be used as line repeaters, with cable lengths longer than 4000 feet, as shown in Figure 23. ...
Page 14
Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers A 120 120 NOTE: RE AND DE ON MAX489/MAX491 ONLY. Figure 22. MAX488–MAX491 Full-Duplex RS-485 Network MAX488–MAX491 A RO 120 ...
Page 15
... MAX483CPA 0°C to +70°C MAX483CSA 0°C to +70°C MAX483CUA 0°C to +70°C MAX483C/D 0°C to +70°C MAX483EPA -40°C to +85°C MAX483ESA -40°C to +85°C MAX483MJA -55°C to +125°C MAX485CPA 0°C to +70°C MAX485CSA 0°C to +70°C MAX485CUA 0°C to +70°C MAX485C/D 0° ...
Page 16
Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers _____________________________________________Chip Topographies (continued) MAX488/MAX490 N.C. N.C. DI GND 0.080" (2.032mm) 16 ______________________________________________________________________________________ 0.054" Z (1.372mm TRANSISTOR COUNT: 248 SUBSTRATE CONNECTED TO GND MAX489/MAX491 ...
Page 17
For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers Package Information 17 ...
Page 18
Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 18 ______________________________________________________________________________________ Package Information (continued) ...
Page 19
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19 © 2003 Maxim Integrated Products ...