MC100EP16 Motorola, MC100EP16 Datasheet

no-image

MC100EP16

Manufacturer Part Number
MC100EP16
Description
Differential Receiver
Manufacturer
Motorola
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC100EP16D
Quantity:
90
Part Number:
MC100EP16DG
Manufacturer:
ON Semiconductor
Quantity:
8
Part Number:
MC100EP16DR2G
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
MC100EP16FDT
Manufacturer:
NO
Quantity:
20 000
Part Number:
MC100EP16FDTR2G
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
MC100EP16TDTR2
Manufacturer:
ON
Quantity:
7 448
Part Number:
MC100EP16VADR2
Manufacturer:
ON
Quantity:
19 897
Part Number:
MC100EP16VBDTR2
Manufacturer:
ON
Quantity:
11 165
Part Number:
MC100EP16VCDTG
Manufacturer:
ON Semiconductor
Quantity:
135
Part Number:
MC100EP16VCDTG
Manufacturer:
ON Semiconductor
Quantity:
165
Part Number:
MC100EP16VCDTR2
Manufacturer:
ON
Quantity:
11 315
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Product Preview
Differential Receiver
equivalent to the EL16 device with higher performance capabilities. With
output transition times significantly faster than the EL16 the EP16 is
ideally suited for interfacing with high frequency sources.
bias for AC coupling to the device. The V BB pin should be used only as a
bias for the EP16 as its current sink/source capability is limited.
Whenever used, the V BB pin should be bypassed to ground via a 0.01 f
capacitor.
force the Q output LOW.
NOTE: Inputs have 75k to V EE on D input and 75k to V EE and V CC on D input
This document contains information on a product under development. Motorola reserves the right to change or
discontinue this product without notice.
3/98
Motorola, Inc. 1998
160ps Propagation Delay
High Bandwidth Output Transitions
75k Internal Input Pulldown Resistors
>1000V ESD Protection
Maximum Frequency > 2.7GHz
V BB Sink/Source Current = 0.5mA maximum
Component Count = 22 NPN devices
The MC10EP16 is a differential receiver. The device is functionally
The EP16 provides a V BB output for either single-ended use or as a DC
Under open input conditions (pulled to V EE ) internal input clamps will
and when left open, force outputs to known state Q=Low, Q=High. Solder
temp 265 C for maximum for < 2–3 seconds; 245 C desired.
Figure 1. 8–Lead Pinout (Top View) and Logic Diagram
V BB
NC
D
D
1
1
2
3
4
75k
75k
75k
8
7
6
5
REV 0
V CC
Q
Q
V EE
PIN
D, D
Q, Q
V BB
8–LEAD PLASTIC SOIC PACKAGE
MC10EP16
PIN DESCRIPTION
CASE 751-06
D SUFFIX
FUNCTION
Data Inputs
Data Outputs
Ref. Voltage Output

Related parts for MC100EP16

MC100EP16 Summary of contents

Page 1

... C for maximum for < 2–3 seconds; 245 C desired Figure 1. 8–Lead Pinout (Top View) and Logic Diagram This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. 3/98 Motorola, Inc. 1998 ...

Page 2

... The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between V PP min and 1V. The lower end of the CMR range is dependent and is equal 2.5V. MOTOROLA Parameter Continuous ...

Page 3

... A 0.5 A –600 Max Min Typ Max Unit 5.5 3.0 5.5 V 2490 2390 2580 mV 1670 1650 1705 mV 2490 2240 2580 mV 1820 1350 1855 mV 150 150 A 0.5 A –600 3.0 3.5 MOTOROLA ...

Page 4

... Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “ ...

Related keywords