MC75174B Motorola, MC75174B Datasheet
MC75174B
Available stocks
Related parts for MC75174B
MC75174B Summary of contents
Page 1
... MC75174B SEMICONDUCTOR TECHNICAL DATA P SUFFIX PLASTIC PACKAGE CASE 648 DW SUFFIX PLASTIC PACKAGE CASE 751D (SO–20L) ORDERING INFORMATION Operating Temperature Range Device Package SO–20L – +85 C SO–20L Plastic DIP MC75174B ...
Page 2
... Leakage in 3–State Mode, –7 Short Circuit Current to Ground p p Short Circuit Current, –7 switched from 0.8 to 2.0 V. Typical values determined ambient and 5.0 V supply. 2 MC75172B MC75174B Symbol Value Unit V CC –0.5, +7.0 Vdc V in +7.0 Vdc I in – – ...
Page 3
... ELECTRICAL CHARACTERISTICS (–40 C Characteristics Inputs Low Level Voltage (Pins 4 & 12, MC75174B only) Low Level Voltage (All Other Pins) High Level Voltage (All Inputs) Current @ 2.7 V (All Inputs) Current @ 0.5 V (All Inputs) Clamp Voltage (All Inputs –18 mA) Thermal Shutdown Junction Temperature Power Supply Current (Outputs Open ...
Page 4
... SK1 = t PLHD – t PHLD for each driver SK2 computed by subtracting the shortest t PLHD from the longest t PLHD of the 4 drivers within a package SK3 computed by subtracting the shortest t PHLD from the longest t PHLD of the 4 drivers within a package. 4 MC75172B MC75174B Figure 2. Common Mode Test OD3 (0 ...
Page 5
... Figure 6. Enable Timing, Differential Outputs 3 3.0 V S.G. p NOTES: 1. S.G. set to: f 1.0 MHz; duty cycle = 50 inverted for Enable measurements. MOTOROLA ANALOG IC DEVICE DATA MC75172B MC75174B 1 PZH(E) V out 110 2 out 1 PZL(E) V out V out 2 ...
Page 6
... Figure 11. Output Differential Voltage versus Load Current 4.0 3 5 4.75 V 1 OUTPUT CURRENT (mA) 6 MC75172B MC75174B Figure 8. Single–Ended Output Voltage 2.0 1. 20.0 mA 1.5 1. 5.25 V 1.0 – 40 – Figure 10. Single–Ended Output Voltage versus Temperature 4 – ...
Page 7
... Driver Pins Inputs – 5.0 – 10 – – 20 – 25 – 0.5 0.5 1.5 2.5 3 INPUT VOLTAGE (V) MOTOROLA ANALOG IC DEVICE DATA MC75172B MC75174B Figure 14. Output Leakage Current 5.0 0 –5.0 –10 –15 –20 9.0 12 –40 – AMBIENT TEMPERATURE ( C) Figure 16. Short Circuit Current versus Common Mode Voltage ...
Page 8
... Description The MC75172B and MC75174B are differential line drivers designed to comply with EIA–485 Standard (April 1983) for use in balanced digital multipoint systems containing multiple drivers. The drivers also comply with EIA–422–A and CCITT Recommendations V.11 and X.27. The drivers meet the EIA– ...
Page 9
... The 60 mentioned above allows for two 120 terminating resistors. Using the EIA–485 requirements (worst case limits), and the graphs of Figures 7 and 9, it can be determined that the maximum current an MC75172B or MC75174B driver will [ source or sink is 65 mA. System Example An example of a typical EIA– ...
Page 10
... NOTES: 1. Terminating resistors R T must be located at the physical ends of the cable. 2. Stubs should be as short as possible. 3. Circuit ground of all drivers and receivers must be connected via a dedicated wire within the cable. Do not rely on chassis ground or power line ground. 10 MC75172B MC75174B Figure 18. Typical EIA–485 System R R TTL ...
Page 11
... Dynamic Input Impedance R in NOTES: 1. Compliance with V.11 and X.27 (Blue book) output impedance requires external resistors in series with the outputs of the MC75172B and MC75174B Bit time. Copies of the EIA Recommendations (EIA–485 and EIA–422–A) can be obtained from the Electronics Industries Association, Washington, D.C. (202– ...
Page 12
... USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com 12 MC75172B MC75174B OUTLINE DIMENSIONS P SUFFIX PLASTIC PACKAGE CASE 648–08 ISSUE R ...