mk2049-45a Integrated Device Technology, mk2049-45a Datasheet
mk2049-45a
Related parts for mk2049-45a
mk2049-45a Summary of contents
Page 1
... Buffer Mode accepts MHz input and will provide a jitter attenuated output at 0.5 x ICLK ICLK ICLK. In this mode the MK2049-45A is ideal for filtering jitter from high frequency clocks. In External Mode, ICLK accepts an 8 kHz clock and will produce output frequencies from a table of common communciations clock rates, CLK and CLK/2 ...
Page 2
... Input clock connection. Connect to 8 kHz backplane or MHz clock. Power Connect to ground. Power Power Supply. Connect to +3.3 V. Loop Connect the loop filter capacitors and resistor between this pin and CAP2. Filter Power Connect to ground. 2 VCXO AND SYNTHESIZER Pin Description MK2049-45A REV B 121809 ...
Page 3
... Please refer to the Output Clock Selection Table on Page 2. Most typical PLL clock devices use an internal VCO (Voltage Controlled Oscillator) for output clock generation. By using a VCXO with an external crystal, the MK2049-45A is able to 3 VCXO AND SYNTHESIZER Pin Description Crystal ...
Page 4
... Quartz Crystal It is important that the correct type of quartz crystal is used with the MK2049-45A. Failure may result in reduced frequency pullability range, inability of the loop to lock, or excessive output phase jitter. The MK2049-45A operates by phase-locking the VCXO circuit to the input signal of the selected ICLK input ...
Page 5
... VDD and the PCB ground plane. To further guard against interfering system supply noise, the MK2049-45A should use one common connection to the PCB power plane as shown in the diagram on the next page. The ferrite bead and bulk capacitor help reduce lower frequency noise in the supply that can lead to output clock phase modulation ...
Page 6
... Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK2049-45A. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied ...
Page 7
... Referenced to jf Mitel/Zarlink MT9045, Note 3 7 VCXO AND SYNTHESIZER Min. Typ. Max. Units 3.15 3.3 3. 0.8 V -10 +10 A -10 + VDD-0.4 V 2.4 V 0.4 V ± VDD V Min. Typ. Max. Units -115 +115 ppm 0 1 400 ps MK2049-45A REV B 121809 ...
Page 8
... Bottom marking: country of origin. IDT™ 3.3 VOLT COMMUNICATIONS CLOCK PLL Symbol Conditions t Referenced to jf Mitel/Zarlink MT9045, Note 3 Relative to ICLK Z OUT Marking Diagram (Pb free VCXO AND SYNTHESIZER Min. Typ. Max. Units 230 ps 0 ppm 2049-45ASILF ###### YYWW 10 1 MK2049-45A REV B 121809 ...
Page 9
... MK2049-45ASITR* MK2049-45ASILF MK2049-45ASILFTR *NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use ...
Page 10
... MK2049-45A 3.3 VOLT COMMUNICATIONS CLOCK PLL Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc ...