mx878 Clare, Inc., mx878 Datasheet
mx878
Related parts for mx878
mx878 Summary of contents
Page 1
... Drawing No. 087809 8-Channel, 60V Relay/Load Driver Open Drain Output, 3 Wire Interface General Description The MX878 channel high voltage switch with 8-bit parallel or serial input control. The MX878 connects directly to a microprocessor through a standard 3 wire serial interface. The open drain pull- down output configuration can drive volts at 200mA ...
Page 2
... Operating Junction Temp Thermal Resistance (Junction to Ambient) ESD Warning ESD (electrostatic discharge) sensitive device. Although the MX878 features proprietary ESD protection circuitry, permanent damage may be sustained if subjected to high energy electrostatic discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. DC Electrical Characteristics o VCC=5 ...
Page 3
... CS Rising to SDO High Z CS Rising to OUT Falling X OUT Fall Time X OE Rising to OUT Rising X OE Rising to OUT Falling X OE Falling to OUT High Z X Note 1: Guaranteed by design. MX878 Drawing No. 087809 Symbol Condition tCSwh tCSs Setup Time tCSwl SCK Low, (parallel input mode tINs 1 tINh 1 ) tSDIs ...
Page 4
... MX878 Serial Timing INx tINs CS* tCSs SCK tSDIs SDI SDO OUTx Parallel Timing INx tINs tINh CS* tCSwl OUTx tOUTf MX878 Drawing No. 087809 tINh tSDIh tSDO tOUTr 4 tCSwh tSDOz tOUTr tOUTf 06/08/06 www.claremicronix.com ...
Page 5
... OUT0 23 OUT1 24 OUT2 25 OUT3 26 OUT4 27 OUT5 28 OUT6 1 OUT7 MX878 Drawing No. 087809 Description High Voltage Supply ( 6V to 60V) No Connect Logic Supply (2.7V to 5.5V) Serial Data Output Parallel Input Parallel Input Parallel Input Parallel Input Parallel Input Parallel Input Parallel Input Parallel Input Serial Clock ...
Page 6
... MX878 Functional Description The MX878 channel high voltage driver with 8-bit input control. The MX878 interfaces to a microprocessor through a standard 3 wire serial interface and an active low chip select, or can be used in a parallel-in, parallel-out configuration. Parallel data is transferred to the I/O register of the MX878 through the parallel input pins, IN0 through IN7 on the falling edge of the chip select pin, CS ...
Page 7
... MX878 Parallel-in / Parallel-out Application IN 8 CS* OE Serial Cascade Application MASTER MASTER OUT MX878 Drawing No. 087809 OUT 8 SDI SCK SDO IN OUT 8 SCK CS* OE SDI SDO IN OUT 8 SCK CS* OE SDI 7 06/08/06 www.claremicronix.com ...
Page 8
... N drive N CS* SDI uC output N SCK SDO input N uC Type 2 timing: capture N CS* SDI don't care SCK SDO input N uC MX878 Drawing No. 087809 MX878 capture IN 8 SDI SDO drive SCK OUT CS analyze N, calculate N+1 analyze N, calculate N capture N+1 drive N+1 uC output N+1 input N+1 ...
Page 9
... Except as set forth in IXYS’ Standard Terms and Conditions of Sale, IXYS Corporation assumes no liability whatsoever, and disclaims any expressed or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right . MX878 Drawing No. 087809 PIN 1 (REF.) MM. ...
Page 10
... The products described in this document are not intended for use in medical implantation or other direct life support applications where malfunction may result in direct physical harm, injury or death to a person. Specification: MX878 ©Copyright 2006, IXYS Corporation All rights reserved. Printed in USA. 10 06/08/06 www ...