NCP511 ON, NCP511 Datasheet
NCP511
Available stocks
Related parts for NCP511
NCP511 Summary of contents
Page 1
... The NCP511 has been designed to be used with low cost ceramic capacitors and requires a minimum output capacitor of 1.0 mF. The device is housed in the micro−miniature TSOP−5 surface mount package ...
Page 2
... Operating Ambient Temperature Storage Temperature 1. This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL−STD−883, Method 3015 Machine Model Method 200 V 2. Latch up capability (85 C) "100 mA DC with trigger voltage. NCP511 Description in. Symbol V in ...
Page 3
... Output Noise Voltage ( 100 kHz Maximum package power dissipation limits must be observed. T J(max qJA 4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. NCP511 ( 1 out(nom.) enable ...
Page 4
... TEMPERATURE ( C) Figure 4. Quiescent Current vs. Temperature INPUT VOLTAGE (V) in Figure 6. Ground Pin Current vs. Input Voltage NCP511 3.5 3.0 2.5 2.0 1.5 1 out 0 100 120 140 Figure 3. Output Voltage vs. Input Voltage ...
Page 5
... out 150 mA out −10 200 400 600 800 1000 1200 TIME (ms) Figure 11. Load Transient Response NCP511 100 50 0 − −100 V out 700 800 900 20 Figure 9. Line Transient Response C out I = 150 mA ...
Page 6
... out 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0.01 0.1 1 FREQUENCY (kHz) Figure 14. Output Noise Density NCP511 = 3 3.0 V out = out out 100 120 140 160 TIME (ms) Figure 13. Turn−On Response 1.5 V out ...
Page 7
... IC operation, bias, etc. When the LDO becomes loaded, this term is called the Ground current actually the difference between the input current (measured through the LDO input pin) and the output current. NCP511 DEFINITIONS Line Regulation The change in output voltage for a change in input voltage. ...
Page 8
... The power dissipated by the NCP511 can be calculated from the following equation: P tot + [ gnd (I out ) ] ) [ out ] * I out 150 mA output current is needed then the ground current from the data sheet is 40 mA. For an NCP511SN30T1 (3.0 V), the maximum input voltage will then be 5.6 V. 100 10 1 ...
Page 9
... Figure 18. Current Boost Regulator The NCP511 series can be current boosted with a PNP transis- tor. Resistor R in conjunction with V of the PNP determines BE when the pass transistor begins conducting; this circuit is not short circuit proof. Input/Output differential voltage minimum is increased the pass resistor ...
Page 10
... NCP511SN25T1G NCP511SN25T1G NCP511SN27T1 NCP511SN27T1G NCP511SN27T1G NCP511SN28T1 NCP511SN28T1G NCP511SN30T1 NCP511SN30T1G NCP511SN33T1 NCP511SN33T1G NCP511SN50T1 NCP511SN50T1G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. NOTE: Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative. ...
Page 11
... TSOP−5/THIN SOT23−5/SC59−5 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NCP511 SN SUFFIX PLASTIC PACKAGE CASE 483−02 ISSUE C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14 ...
Page 12
... USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 12 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NCP511/D ...