STR-P711 Olimex Ltd., STR-P711 Datasheet
STR-P711
Specifications of STR-P711
Available stocks
Related parts for STR-P711
STR-P711 Summary of contents
Page 1
... STR-P711 development board All boards produced by Olimex are ROHS compliant Copyright(c) 2010, OLIMEX Ltd, All rights reserved Users Manual Revision C, June 2010 Page 1 ...
Page 2
... INTRODUCTION STR-P711 is development board with high performance STR711FR2T6 ARM7TDMI ports serial interfaces such as USB, UART and other. On the board are available JTAG, SD/MMC card connector, UEXT, EXT, USB two RS232 connectors. All this can be used in a wide range of applications. BOARD FEATURES TM microcontroller from STMicroelectronics ...
Page 3
... ELECTROSTATIC WARNING The STR-P711 board is shipped in protective anti-static packaging. The board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. BOARD USE REQUIREMENTS Cables: The cable you will need depends on the programmer/debugger you use. If you use ARM-JTAG-EW, you will need USB A-B cable, if you use you will need LPT cable ...
Page 4
Timers 16-bit watchdog timer Four 16-bit timers each with: 2 input captures, 2 output compares, PWM and pulse counter modes Communications Interfaces interfaces (1 multiplexed with SPI) 4 UART asynchronous serial communications interfaces Smart Card ...
Page 5
BLOCK DIAGRAM Page 5 ...
Page 6
MEMORY MAP Page 6 ...
Page 7
SCHEMATIC 1 2 RST 3 R42 10K + + + + 470uF/16V C70 USB Page 7 BC846 Q3 ...
Page 8
... BOARD LAYOUT POWER SUPPLY CIRCUIT STR-P711 can take power (+9 VDC or 6VAC) from PWR_JACK, and (+5 V) from USB. The programmed board power consumption is about 90 mA with all peripherals enabled. RESET CIRCUIT STR-P711 reset circuit includes R32 (4.7k), U3 (MCP130), JTAG connector pin 15 and RESET button. ...
Page 9
... JUMPER DESCRIPTION STNBY When this jumper is open, STR711FR2T6 pin 23 (/STDBY) is connected to pull-up resistor R46 (100k); when jumper STNBY is closed, STR711FR2T6 pin 23 (/STDBY) is connected to ground. Default state is open. INPUT/OUTPUT Status led (red) with name LED1 connected to STR711FR2T6 pin 41 (P1.8). Status led (red) with name LED2 connected to STR711FR2T6 pin 45 (P1.9). ...
Page 10
EXTERNAL CONNECTORS DESCRIPTION RS232_0 Pin # RS232_1 Pin # Signal Name NC T1OUT R1IN Via 0 Ohm to pin 6 GND Via ...
Page 11
PWR_JACK Pin # Signal Name 1 Power Input 2 UEXT Pin # Signal Name 1 3.3V 2 GND 3 U3TX/MISO0 4 U3RX/MOSI0 5 SCL1/SCLK0 6 SDA1/SS0 7 MISO1 8 MOSI1 9 SCLK1 10 SS1 USB Pin # Signal Name 1 ...
Page 12
... JTAG The JTAG connector allows the software debugger to talk via a JTAG (Joint Test Action Group) port directly to the core. Instructions may be inserted and executed by the core thus allowing STR711F memory to be programmed with code and executed step by step by the host software. ...
Page 13
EXT Page 13 ...
Page 14
SD/MMC Pin # 1 SS1 3 GND 5 SCLK1 7 MISO1 9 pull- pull-up Signal Name Pin # Page 14 Signal Name MOSI1 VCC GND pull- ...
Page 15
MECHANICAL DIMENSIONS Page 15 ...
Page 16
... AVAILABLE DEMO SOFTWARE – Buttons and LEDs – Sample mouse driver with STR711 – UART routines – SD/MMC read/write routines Page 16 ...
Page 17
... ORDER CODE STR-P711 microcontroller How to order? You can order to us directly or by any of our distributors. Check our web Revision history Revision C, June 2010 - assembled and tested board, includes STR711FR2T6 www.olimex.com/dev for more info. Page 17 ...
Page 18
... However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product ...