PC3SD11NTZ SHARP [Sharp Electrionic Components], PC3SD11NTZ Datasheet

Page 1

... Series ∗ Zero cross type is also available. (PC3SD21NTZ Series) ■ Description PC3SD11NTZ Series Phototriac Coupler include an infrared emitting diode (IRED) optically coupled to an output Phototriac. These devices feature full wave control and are ideal isolated drivers for medium to high current Triacs. ...

Page 2

... Internal Connection Diagram ■ Outline Dimensions 1. Through-Hole [ex. PC3SD11NTZ] ±0.3 1.2 ±0.2 0.6 Model No. SHARP mark Rank mark "S" Anode mark Date code (2 digit Factory identification mark ±0.5 7.12 ±0.1 0.5 ±0.25 2.54 θ Product mass : approx. 0.35g 3. SMT Gullwing Lead-Form [ex. PC3SD11NXP] ± ...

Page 3

... Anode 4 mark 1 VDE identification mark 7.12 ±0.3 7.62 ±0.25 Epoxy resin 2.54 +0.4 1.0 −0 +0 10.0 −0.5 Product mass : approx. 0.34g 3 PC3SD11NTZ Series (Unit : mm) ±0.3 1.2 4 Model No. Rank mark Date code (2 digit Factory identification mark ±0.3 ±0.5 7.62 Epoxy resin ±0.5 10.16 ±0.1 0.5 ±0.3 1 Model No ...

Page 4

... Please contact the local SHARP sales representative to see the actural status of the production. Rank mark Refer to the Model Line-up table 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D Japan Indonesia Philippines China 4 PC3SD11NTZ Series Sheet No.: D2-A07501EN ...

Page 5

... D − dV/dt V =1/√ Rank =6V, R Rank Rank C R DC500V,40 to 60%RH ISO t V =6V, R =100Ω PC3SD11NTZ Series Soldering area MIN. TYP. MAX. − 1.2 1.4 − − 10 − − 1 DRM − − 2.5 0.1 − 3.5 ·V 1 000 2 000 − DRM − ...

Page 6

... Sleeve 50pcs/sleeve - Approved - PC3SD11NXZA PC3SD11YXZA PC3SD11NVZA PC3SD11YVZA PC3SD11NXZB PC3SD11YXZB PC3SD11NVZB PC3SD11NXZC PC3SD11YXZC PC3SD11NVZC PC3SD11YVZC SMT Gullwing Wide SMT Gullwing Taping 1 000pcs/reel - Approved - PC3SD11NXPB PC3SD11YXPB PC3SD11NWPB 6 PC3SD11NTZ Series I [mA =6V, Rank mark D R =100Ω) L Approved MAX.10 A MAX.7 PC3SD11YVZBF B MAX [mA ...

Page 7

... Fig.3-b Forward Current vs. Forward Voltage 2 2.5 3 (V) F Fig.4-b Minimum Trigger Current vs. Ambient V = =100Ω 100 (˚ PC3SD11NTZ Series 175 150 125 100 − Ambient temperature T (˚C) a (Rank B, Rank C) 100 T =75˚ 50˚C 25˚ ...

Page 8

... Fig.8 Repetitive Peak OFF-state Current vs. Ambient Temperature 100 (˚C) a Fig.9-b Turn-on Time vs. Forward Current 1 000 V = =100Ω =25˚C a 100 (mA) 8 PC3SD11NTZ Series I =100mA T 2.4 2.2 2 1.8 1.6 1.4 1.2 1 −40 − Ambient temperature T (˚C) a −6 V =600V D −7 −8 −9 − ...

Page 9

... Therefore in order to maintain proper operation, a design implementing these Phototriac Couplers should provide at least twice the minimum required triggering current from initial operation. ● Recommended Foot Print (reference) SMT Gullwing Lead-form 8.2 2.2 PC3SD11NTZ Series ) must be 0.1mA or less. F Wide SMT Gullwing Lead-form 10.2 2.2 9 (Unit : mm) Sheet No ...

Page 10

... Note) Please add the snubber circuit according to a condition. Any snubber or varistor used for the above mentioned scenarios should be located as close to the main output triac as possible. ✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes. 6 Load AC Line 5 Triac 4 10 PC3SD11NTZ Series Sheet No.: D2-A07501EN ...

Page 11

... Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. Reflow 220˚C or more, 60s or less PC3SD11NTZ Series 4 (min) Sheet No.: D2-A07501EN ...

Page 12

... This product shall not contain the following materials. And they are not used in the production process for this device. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. PC3SD11NTZ Series 12 Sheet No.: D2-A07501EN ...

Page 13

... MAX. 50pcs of products shall be packaged in a sleeve. Both ends shall be closed by tabbed and tabless stoppers. The product shall be arranged in the sleeve with its anode mark on the tabless stopper side. MAX. 20 sleeves in one case. Sleeve outline dimensions 15.0 6.35 PC3SD11NTZ Series 13 (Unit : mm) (Unit : mm) Sheet No.: D2-A07501EN ...

Page 14

... Direction of product insertion ±0.1 ±0.1 ±0.1 ±0.1 1.75 12.0 2 ±0.05 ±0.1 ±0.1 4.2 7.8 Dimensions List f b Pull-out direction 14 PC3SD11NTZ Series J I (Unit:mm ±0.1 +0.1 4.0 φ1.5 −0 (Unit : mm ±1.5 ±1.0 ±0.5 330 17.5 100 ±1.0 ±0.5 ±0 ...

Page 15

... Direction of product insertion ±0.1 ±0.1 ±0.1 ±0.1 1.75 12.0 2 ±0.05 ±0.1 ±0.1 4.15 7.6 Dimensions List f b Pull-out direction 15 PC3SD11NTZ Series J I (Unit : mm ±0.1 +0.1 4.0 φ1.5 −0 (Unit : mm ±1.5 ±1.0 ±0.5 330 25.5 100 ±1.0 ±0.5 ±0.5 23 2.0 2 ...

Page 16

... Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection PC3SD11NTZ Series with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) ...