SSM2250 Analog Devices, SSM2250 Datasheet
SSM2250
Specifications of SSM2250
Available stocks
Related parts for SSM2250
SSM2250 Summary of contents
Page 1
... The ability to shut down the amplifiers, (60 A shutdown current) makes the SSM2250 an ideal speaker amplifier for battery-powered applications. The SSM2250 is specified over the industrial (– +85 C) temperature range available in 14-lead TSSOP and 10-lead MSOP surface mount packages. SoundMax is a registered trademark of Analog Devices, Inc. ...
Page 2
... SSM2250–SPECIFICATIONS ELECTRICAL CHARACTERISTICS Parameter DEVICE CHARACTERISTICS Output Offset Voltage Large Signal Voltage Gain Output Power Output Impedance SHUTDOWN INPUT Input Voltage High Input Voltage Low POWER SUPPLY Supply Current Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin ...
Page 3
... V Common-Mode Input Voltage . . . . . . . . . . . . . . . . . . . . 6 V ESD Susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V Storage Temperature Range RM, RU Packages . . . . . . . . . . . . . . . . . . – +150 C Operating Temperature Range SSM2250 . . . . . . . . . . . . . . . . . . . . . . . . . . – +85 C Junction Temperature Range RM, RU Packages . . . . . . . . . . . . . . . . . . – +165 C Lead Temperature Range (Soldering, 60 sec 300 C NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause perma- nent damage to the device. This is a stress rating only ...
Page 4
... SSM2250 BTL MODE OUT 0.1 20 100 1k FREQUENCY – Hz Figure 2. BTL Out THD + N vs. Frequency 2.7V S BTL MODE 0.25W OUT 0.1 20 100 1k FREQUENCY – Hz Figure 3. BTL Out THD + N vs. Frequency VARIES 2.7V S BTL MODE 1kHz 0.1 10m 100m OUTPUT POWER – W Figure 4. THD + N vs. Output Power ...
Page 5
... Figure 9. BTL Out THD + N vs. Output Power at 20 kHz REV MODE 20Hz 0.1 0. Figure 10. SE Out THD + N vs. Output Power MODE 20kHz 0.1 0. Figure 11. SE Out THD + N vs. Output Power at 20 kHz –5– SSM2250 100 200 OUTPUT POWER – mW 100 200 OUTPUT POWER – mW ...
Page 6
... Once a plug is inserted, this connection is broken. Referring to Figure 12, Pin 4 of the SSM2250 is connected to the normalizing pin for the right channel output. This is the pin in the headphone jack that will hit the ring on the headphone plug. ...
Page 7
... will create a corner frequency of 8 Hz. This is acceptable, as the PC 99 audio requirement specifies the com- puter audio system bandwidth kHz. Pin 10 on the SSM2250 provides the proper bias voltage for the amplifiers. A 0.1 F capacitor should be connected here to reduce sensitivity to noise on the power supply. A larger capaci- tor can be used should more rejection from power supply noise be required ...
Page 8
... It can be easily seen that power into a speaker can produce quite a bit of acoustic energy Shutdown Feature L The SSM2250 can be put into a low power consumption shut- down mode by connecting Pin SSM2250 has low supply current Pin 3 should be connected to ground for normal operation. Con- necting Pin ...
Page 9
... The AD1881 is an AC’97 Ver. 2.1 audio codec available from Analog Devices. The stereo output from the AD1881 is coupled into the SSM2250, which is used to drive a mono internal speaker and stereo headphones. The internal speaker switching is controlled by the SSM2250 through the normalizing pin on the headphone jack ...
Page 10
... SSM2250 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 10-Lead MSOP (RM Suffix) 0.124 (3.15) 0.112 (2.84 0.124 (3.15) 0.199 (5.05) 0.112 (2.84) 0.187 (4.75 PIN 1 0.0197 (0.50) BSC 0.122 (3.10) 0.110 (2.79) 0.038 (0.97) 0.043 (1.09) 0.030 (0.76) 0.037 (0.94) SEATING 0.006 (0.15) ...