TDA1305 Philips Semiconductors, TDA1305 Datasheet
TDA1305
Available stocks
Related parts for TDA1305
TDA1305 Summary of contents
Page 1
... DATA SHEET TDA1305T Stereo 1fs data input up-sampling filter with bitstream continuous dual DAC (BCC-DAC2) Preliminary specification Supersedes data of September 1994 File under Integrated Circuits, IC01 INTEGRATED CIRCUITS 1995 Dec 08 ...
Page 2
... No analog post filtering required Superior signal-to-noise ratio Wide dynamic range (18-bit) Single rail supply (3.4 to 5.5 V). GENERAL DESCRIPTION The TDA1305T is a new generation of filter-DAC which features a unique combination of bitstream and continuous calibration techniques. The converter functions as a ORDERING INFORMATION TYPE NUMBER ...
Page 3
... 1.425 DDD DDA DDO signal level signal level signal level; A-weighted A-weighting; 100 at code 00000H = 48 kHz; normal speed kHz; double speed s 6 Preliminary specification TDA1305T TYP. MAX. UNIT 5.0 5.5 V 5.0 5.5 V 5 1.5 1.575 V ...
Page 4
... Philips Semiconductors Stereo 1fs data input up-sampling filter with bitstream continuous dual DAC (BCC-DAC2) BLOCK DIAGRAM 1995 Dec 08 Fig.1 Block diagram. 4 Preliminary specification TDA1305T ...
Page 5
... VOR 25 right channel output V 26 internal reference voltage for output ref channels (0. operational amplifier ground SSO V 28 operational amplifier supply voltage DDO 1995 Dec 08 32 kHz, DEEM 32 kHz, DEEM ) DD 5 Preliminary specification TDA1305T Fig.2 Pin configuration. ...
Page 6
... Dec 08 provide a system clock of 256 or 384f 48 kHz). The system frequency is selectable by means of pin CLKS1 and pin CLKS2. The SYSCLKO output (pin 16) provides the system clock for external use. input s The TDA1305T supports the following data input modes 256f ) in the s sys s ...
Page 7
Fig.3 Input formats. ...
Page 8
... A sample-and-hold section which provides another 6 times oversampling to 48 times. The zero-order hold characteristic of this sample-and-hold section plus the 1st order analog filtering remove the spectral components around 8f Pass-band ripple and stop-band attenuation for double-speed are given in Table 3. 8 Preliminary specification TDA1305T . ...
Page 9
... The dual 5-bit DAC uses the continuous calibration technique. This method, based on charge storage, involves exact duplication of a single reference current source. In the TDA1305T, 32 such current sources plus 1 spare source are continuously calibrated. The spare source is included to allow continuous converter operation. ...
Page 10
... DDO at code 00000H note 2 DDA f = 384f sys 256f sys s note 3 note 3 note 384f sys 256f sys s note 3 note 3 note 0 0 note 5 note 5 10 Preliminary specification TDA1305T MIN. TYP. MAX. 3.4 5.0 5 3.4 5.0 5.5 5.5 8 3.4 5.0 5.5 6 9.6 16.93 18.4 6.4 11.29 12.28 0.5 0. 104 59 ...
Page 11
... Hz. Ripple rejection ripple . The value here assumes that C ref are peak values to allow for transients. IH measured 5.5 V. LImax unless otherwise specified. amb CONDITIONS 11 Preliminary specification TDA1305T MIN. TYP. MAX. 48f s 64f ...
Page 12
... kHz); note 4 A weighted; 100 at code (00000H RANGE CONDITIONS kHz 14 kHz 24.1 to 150 kHz typical worst case 150 kHz to infinity typical worst case 17 to 17.5 kHz 12 Preliminary specification TDA1305T TYP. MAX. UNIT 0.003 0.009 % 0.63 1 0.5 % ...
Page 13
... CHARACTERISTICS 0 0.075 dB 0.3 dB (min (max (max (max (max.) TDA1305T ...
Page 14
... Philips Semiconductors Stereo 1fs data input up-sampling filter with bitstream continuous dual DAC (BCC-DAC2) APPLICATION INFORMATION 1995 Dec 08 Fig.5 Application diagram. 14 Preliminary specification TDA1305T ...
Page 15
... The (THD + N)/S was measured over a bandwidth kHz and filtered with A-weighted characteristics. The graph was constructed from average measurement values of a small amount of engineering samples. No guarantee for typical values is implied. 15 Preliminary specification TDA1305T ...
Page 16
... Philips Semiconductors Stereo 1fs data input up-sampling filter with bitstream continuous dual DAC (BCC-DAC2) Fig.7 Total harmonic distortion as a function of signal level; (A-weighted). 1995 Dec 08 16 Preliminary specification TDA1305T ...
Page 17
... EIAJ MS-013AE 17 Preliminary specification detail 10.65 1.1 1.1 0.25 0.25 1.4 10.00 0.4 1.0 0.419 0.043 0.043 0.055 0.01 0.01 0.394 0.016 0.039 EUROPEAN PROJECTION TDA1305T SOT136 ( 0.9 0.1 0 0.035 0.004 0.016 ISSUE DATE 95-01-24 97-05-22 ...
Page 18
... Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 18 Preliminary specification TDA1305T ...
Page 19
... Philips customers using or selling these products for use in such applications their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1995 Dec 08 19 Preliminary specification TDA1305T ...
Page 20
... CA 94088-3409, Tel. (800)234-7381, Fax. (708)296-8556 Uruguay: Coronel Mora 433, MONTEVIDEO, Tel. (02)70-4044, Fax. (02)92 0601 Internet: http://www.semiconductors.philips.com/ps/ For all other countries apply to: Philips Semiconductors, International Marketing and Sales, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Telex 35000 phtcnl, Fax. +31-40-2724825 SCD47 © ...