TDA5144 Philips Semiconductors, TDA5144 Datasheet
TDA5144
Available stocks
Related parts for TDA5144
TDA5144 Summary of contents
Page 1
... DATA SHEET TDA5144 Brushless DC motor drive circuit Product specification Supersedes data of March 1992 File under Integrated Circuits, IC11 Philips Semiconductors INTEGRATED CIRCUITS June 1994 ...
Page 2
... APPLICATIONS General purpose spindle driver (e.g. for hard disk) Laser beam printer. GENERAL DESCRIPTION The TDA5144 is a bipolar integrated circuit used to drive 3-phase brushless DC motors in full-wave mode. The device is sensorless (saving of 3 hall-sensors) using the back-EMF sensing technique to sense the rotor position. ...
Page 3
... Fig.1 Block diagram (SOT163-1; SO20L). 3 Product specification TDA5144 ...
Page 4
... Product specification TDA5144 ...
Page 5
... Brushless DC motor drive circuit Fig.2 Pin configuration (SOT163-1; SO20L). FUNCTIONAL DESCRIPTION The TDA5144 offers a sensorless three phase motor drive function unique in its combination of sensorless motor drive and full-wave drive. The TDA5144 offers protected outputs capable of handling high currents and can be used with star or delta connected motors ...
Page 6
... June 1994 CONDITIONS see Figs 4 and 5 see Chapter “Handling” MBD536 3 P tot ( 150 200 amb Fig.5 Power derating curve (SOT136-1; SO28L). 6 Product specification TDA5144 MIN. MAX 0.5 P 0.5 17 GND VMOT 2.5 55 +150 0 +70 500 50 ...
Page 7
... VMOT see Fig.6 VMOT see Fig.6 VMOT ) I = 500 mA notes 4 and 5; see Fig 500 mA notes 4 and 5; see Fig.1 note 5 7 Product specification TDA5144 MIN. TYP. MAX 6.3 7 130 140 150 0 VMOT ...
Page 8
... 0 330 ; 1.5 2.5 0.2 V < V < 0.3 V CAP-TI 0.3 V < V < 2.2 V CAP-TI 10.6 5.3 1.85 800 2.3 10.1 20.9 0.9 800 2.3 8 Product specification TDA5144 TYP. MAX. UNIT mA 1.5 2 2.0 2.5 A 2.0 1.5 A 0. ...
Page 9
... The outputs are short-circuit protected by limiting the current and the IC temperature. APPLICATION INFORMATION (1) Value selected for 3 Hz start-up oscillator frequency. Fig.7 Application diagram without use of the operational transconductance amplifier (OTA). June 1994 ; P Fig.6 Output transition time measurement. 9 Product specification TDA5144 ...
Page 10
... If the movement of the motor generates enough EMF the TDA5144 will run the motor. If the amount of EMF generated is insufficient, then the motor will move one step only and will oscillate in its new position. The amplitude of ...
Page 11
... Hz; so: 6231 CAP-CD 15.6 (choose 18 nF) = ------------ - = 400 The other capacitor, CAP-DC, is used to repeat the same delay by charging and discharging with 15.5 A. The same value can be chosen as for CAP-CD. Figure 9 illustrates typical voltage waveforms. June 1994 3 10 N.m/ (CAP-CD AND 11 Product specification TDA5144 ...
Page 12
... Fig.8 Typical application of the TDA5144 as a scanner driver, with use of OTA. June 1994 ...
Page 13
... CAP- recommended. To ensure a good start-up and commutation, care must be taken that no oscillations occur at the trailing edge of the flyback pulse. Snubber networks at the outputs should be critically damped. Typical voltage waveforms are illustrated by Fig.10. 13 Product specification TDA5144 ...
Page 14
... Possibilities of motor control Reliability. FG SIGNAL The FG signal is generated in the TDA5144 by using the zero-crossing of the motor EMF from the three motor windings. Every zero-crossing in a (star connected) motor winding is used to toggle the FG output signal. The FG frequency is therefore half the commutation frequency. All transitions indicate the detection of a zero-crossing ...
Page 15
... It is possible, that when braking, the motor voltage (via the flyback diodes and the impedance on VMOT) may cause higher currents than allowed ( 0.6 A). These currents must be limited externally. June 1994 15 Product specification TDA5144 ...
Page 16
... Philips Semiconductors Brushless DC motor drive circuit PACKAGE OUTLINES handbook, full pagewidth S 0.9 (4x) 0.4 20 pin 1 index 1 Dimensions in mm. Fig.11 Plastic small outline package; 20 leads; large body (SOT163-1; SO20L). June 1994 13.0 12.6 0 0.49 0.25 M 0.36 1.27 (20x) 16 Product specification 7.6 7.4 10.65 10.00 1.1 1.0 2.45 0.3 0.32 2.25 0.1 0.23 1.1 0 detail A TDA5144 A 2.65 2.35 o MBC234 - 1 ...
Page 17
... Philips Semiconductors Brushless DC motor drive circuit handbook, full pagewidth S 0.9 (4x) 0.4 28 pin 1 index 1 Dimensions in mm. Fig.12 Plastic small outline package; 28 leads; large body (SOT136-1; SO28L). June 1994 18.1 17.7 0 0.49 0.25 M 0.36 1.27 (28x) 17 Product specification TDA5144 7.6 7.4 10.65 10.00 1.1 1.0 2.45 0.3 2.25 0.32 0.1 0.23 1.1 0 detail A A 2.65 2.35 o MBC236 - 1 ...
Page 18
... C. (Pulse-heated soldering is not recommended for SO packages.) For pulse-heated solder tool (resistance) soldering of VSO packages, solder is applied to the substrate by dipping extra thick tin/lead plating before package placement. 18 Product specification TDA5144 - HELD SOLDERING ) ...
Page 19
... Philips Semiconductors Brushless DC motor drive circuit June 1994 NOTES 19 Product specification TDA5144 ...
Page 20
... Bangkok 10260, THAILAND, Tel. (662)398-0141, Fax. (662)398-3319. Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL, Tel. (0 212)279 2770, Fax. (0212)269 3094 United Kingdom: Philips Semiconductors Limited, P.O. Box 65, Philips House, Torrington Place, LONDON, WC1E 7HD, Tel. (071)436 41 44, Fax. (071)323 03 42 United States: INTEGRATED CIRCUITS: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel ...