X25057 Xicor, X25057 Datasheet
X25057
Available stocks
Related parts for X25057
X25057 Summary of contents
Page 1
... ID and parametric data in different portions of the E ranging from as little as one page to as much as 1/2 of the total array. The X25057 also features a WP pin that can be used for hardwire protection of the part, disabling all write attempts, as well as a Write Enable Latch that must be set before a write operation can be initiated. The X25057 utilizes Xicor’ ...
Page 2
... SO pin change after the falling edge of the clock input. Chip Select (CS) When CS is HIGH, the X25057 is deselected and the SO output pin is at high impedance and unless an internal write operation is underway, the X25057 will be in the standby power mode. CS LOW enables the X25057, placing it in the active power mode ...
Page 3
... LOW and remain LOW for the duration of the operation. The host may continue to write bytes of data to the X25057. The only restriction is the 16 bytes must reside on the same page. If the address counter reaches the end of the page and the clock continues, the counter will “ ...
Page 4
... READ: Read operation followed by address *Instructions are shown with MSB in leftmost position. Instructions are transferred MSB first. Operational Notes The X25057 powers up in the following state: • The device is in the low power, standby state. • A HIGH to LOW transition required to enter an active state and receive an instruction. • ...
Page 5
... X25057 Figure 2. Read Operation Sequence SCK READ INSTRUCTION (1 BYTE) SI HIGH IMPEDANCE SO Figure 3. Read Status Operation Sequence SCK READ STATUS INSTRUCTION SI NONVOLATILE WRITE IN PROGRESS BYTE ADDRESS (2 BYTE ...
Page 6
... X25057 Figure 4. WREN/WRDI Sequence CS SCK SI SO Figure 5. Byte Write Operation Sequence SCK WRITE INSTRUCTION (1 BYTE) SI HIGH IMPEDANCE INSTRUCTION (1 BYTE) HIGH IMPEDANCE BYTE ADDRESS (2 BYTE 7033 FRM F05 ...
Page 7
... X25057 Figure 6. Page Write Operation Sequence SCK PROGRAM INSTRUCTION SCK DATA BYTE Figure 7. IDLock Operation Sequence CS 0 SCK SI HIGH IMPEDANCE BYTE ADDRESS ...
Page 8
... Exposure to absolute maximum rating con- ditions for extended periods may affect device reliability. Supply Voltage Max. X25057 +70 C X25057-2.7 +85 C X25057-1.8 7033 FRM T04 Limits Min. Max. Units 3 400 – ...
Page 9
... X25057 CAPACITANCE 1MHz Symbol (3) C Output Capacitance (SO) OUT (3) C Input Capacitance (SCK, SI, CS, WP) IN EQUIVALENT A.C. LOAD CIRCUIT 5V 2061 2696 OUTPUT OUTPUT 3025 5288 30pF A.C. CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.) Data Input Timing Symbol Parameter ...
Page 10
... X25057 Data Output Timing Symbol Parameter f Clock Frequency SCK t Output Disable Time DIS t Output Valid from Clock LOW V t Output Hold Time HO (5) t Output Rise Time RO (5) t Output Fall Time FO Notes: (5) This parameter is periodically sampled and not 100% tested. Figure 8. Serial Output Timing ...
Page 11
... X25057 Figure 9. Serial Input Timing CS t LEAD SCK MSB IN HIGH IMPEDANCE LAG t FI LSB IN 7033 FRM F11 ...
Page 12
... X25057 PACKAGING INFORMATION 8-LEAD MINIATURE SMALL OUTLINE GULL WING PACKAGE TYPE M 0.012 + 0.006 / -0.002 0.040 (1.02 0.007 (0.18) 0.005 (0.13) NOTE: 1. ALL DIMENSIONS IN INCHES AND (MILLIMETERS) 0.118 0.002 (3.00 0.05) (0.30 + 0.15 / -0.05) 0.118 0.002 (3.00 0.05) 0.030 (0.76) 0.0216 (0.55) 7 TYP 0.036 (0.91) 0.032 (0.81) 0.002 0.008 (0.20) 0.05) 0.004 (0.10) 0.150 (3.81) REF. 0.193 (4.90) REF. 12 0.0256 (0.65) TYP R 0 ...
Page 13
... X25057 PACKAGING INFORMATION 0 – 8 See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN P ARENTHESES IN MILLIMETERS) 8-LEAD PLASTIC, TSSOP , PACKAGE TYPE V .025 (.65) BSC .169 (4.3) .252 (6.4) BSC .177 (4.5) .114 (2.9) .122 (3.1) .047 (1.20) .0075 (.19) .002 (.05) .0118 (.30) .006 (.15) .010 (.25) .019 (.50) .029 (.75) Detail A (20X) 13 Gage Plane Seating Plane ...
Page 14
... X25057 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX 0.010 (0.25) 0.020 (0.50) 0 – 8 0.016 (0.410) 0.037 (0.937) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) PIN 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7 0.050 (1.27 0.0075 (0.19) 0.250" 0.010 (0.25) FOOTPRINT 14 0.150 (3.80) 0.228 (5.80) 0.158 (4.00) ...
Page 15
... X25057 PACKAGING INFORMATION 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) MAX. TYP . 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH 0.430 (10.92) 0.360 (9.14) PIN 1 INDEX PIN 1 0.300 (7.62) REF. SEATING PLANE 0.150 (3.81) ...
Page 16
... F = 2.7 to 5.5V + 2.7 to 5.5V, -40 to +85 C Blank = 4.5 to 5.5V + 4.5 to 5.5V, - Limits 8-Lead SOIC/PDIP Blank = 8-Lead SOIC X25057 8-Lead PDIP 1.8 to 3.6V + 1.8 to 3.6V, - 2.7 to 5.5V + 2.7 to 5.5V, -40 to +85 C Blank = 4.5 to 5.5V + 4.5 to 5.5V, -40 to +85 C ...