PIC12F635-I/P Microchip Technology, PIC12F635-I/P Datasheet - Page 137

• Manufacturer Part Number: PIC12F635-I/P
• Description: IC MCU FLASH 1KX14 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F635-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 5
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS- 232/SPI/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120, DM163029, DV164101, DM163014
• Minimum Operating Temperature: - 40 C
• Data Rom Size: 128 B
• Height: 3.3 mm
• Length: 9.27 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163029 - BOARD PICDEM FOR MECHATRONICSAC162057 - MPLAB ICD 2 HEADER 14DIPACICE0201 - MPLABICE 8P 300 MIL ADAPTERAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.7
On power-up, the time-out sequence is as follows: first,
PWRT time-out is invoked after POR has expired, then
OST is activated after the PWRT time-out has expired.
The total time-out will vary based on oscillator
Configuration and PWRTE bit status. For example, in
EC mode with PWRTE bit erased (PWRT disabled),
there will be no time-out at all. Figure 12-4, Figure 12-5
and Figure 12-6 depict time-out sequences. The device
can execute code from the INTOSC, while OST is active,
by enabling Two-Speed Start-up or Fail-Safe Clock
Monitor (See Section 3.7.2 “Two-Speed Start-up
Sequence”
Monitor”).
Since the time-outs occur from the POR pulse, if MCLR
is kept low long enough, the time-outs will expire. Then
bringing MCLR high will begin execution immediately
(see Figure 12-5). This is useful for testing purposes or
to
PIC12F635/PIC16F636/639 device operating in parallel.
Table 12-5 shows the Reset conditions for some
special registers, while Table 12-4 shows the Reset
conditions for all the registers.
TABLE 12-1:
TABLE 12-2:
TABLE 12-3:
© 2007 Microchip Technology Inc.
XT, HS, LP
RC, EC, INTOSC
CONFIG
PCON
STATUS
Legend:
Note
Legend: u = unchanged, x = unknown
Configuration
Name
POR
Oscillator
0
u
u
u
u
u
u
u
1:
2:
(2)
synchronize
Time-out Sequence
BOREN1 BOREN0
u = unchanged, x = unknown, – = unimplemented bit, reads as ‘0’, q = value depends on condition. Shaded cells are not used by BOR.
Other (non Power-up) Resets include MCLR Reset and Watchdog Timer Reset during normal operation.
See Configuration Word register (Register 12-1) for operation of all register bits.
Bit 9
BOR
and
x
0
u
u
u
u
u
0
TIME-OUT IN VARIOUS SITUATIONS
SUMMARY OF REGISTERS ASSOCIATED WITH BROWN-OUT RESET
PCON BITS AND THEIR SIGNIFICANCE
T
Section 3.8
PWRT
Bit 8
WUR
PWRTE = 0
x
u
u
u
u
u
0
u
more
+ 1024 • T
T
PWRT
Bit 7
CPD
IRP
—
Power-up
“Fail-Safe
TO
OSC
1
1
0
0
u
1
1
1
Bit 6
RP1
CP
—
than
ULPWUE SBOREN
PWRTE = 1
1024 • T
MCLRE
Bit 5
RP0
PD
Clock
1
1
u
0
u
0
0
1
PIC12F635/PIC16F636/639
—
one
OSC
PWRTE
Power-on Reset
Brown-out Reset
WDT Reset
WDT Wake-up
MCLR Reset during normal operation
MCLR Reset during Sleep
Wake-up Reset during Sleep
Brown-out Reset during Sleep
Bit 4
TO
T
PWRT
12.8
The Power Control register, PCON (address 8Eh), has
two Status bits to indicate what type of Reset that last
occurred.
Bit 0 is BOR (Brown-out). BOR is unknown on
Power-on Reset. It must then be set by the user and
checked on subsequent Resets to see if BOR = 0,
indicating that a Brown-out has occurred. The BOR
Status bit is a “don’t care” and is not necessarily
predictable if the brown-out circuit is disabled
(BOREN<1:0> = 00 in the Configuration Word
register).
Bit 1 is POR (Power-on Reset). It is a ‘0’ on Power-on
Reset and unaffected otherwise. The user must write a
‘1’ to this bit following a Power-on Reset. On a
subsequent Reset, if POR is ‘0’, it will indicate that a
Power-on Reset has occurred (i.e., V
gone too low).
For more information, see Section 4.2.3 “Ultra
Low-Power Wake-up” and Section 12.6 “Brown-out
Reset (BOR)”.
WDTE
WUR
Bit 3
PD
PWRTE = 0
+ 1024 • T
T
PWRT
FOSC2
Brown-out Reset
Bit 2
Power Control (PCON) Register
—
Z
FOSC1
OSC
Bit 1
POR
DC
Condition
FOSC0
1024 • T
PWRTE = 1
Bit 0
BOR
C
—
--01 --qq
0001 1xxx
POR, BOR
OSC
Value on
—
DS41232D-page 135
DD
1024 • T
from Sleep
Wake-up
--0u --uu
000q quuu
may have
Resets
Value on
all other
—
—
OSC
(1)