ATTINY85-20SU Atmel, ATTINY85-20SU Datasheet - Page 11

• Manufacturer Part Number: ATTINY85-20SU
• Description: IC AVR MCU 8K 20MHZ 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY85-20SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIPATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.6
4.6.1
2586M–AVR–07/10
Stack Pointer
SPH and SPL — Stack Pointer Register
Figure 4-3.
In the different addressing modes these address registers have functions as fixed displacement,
automatic increment, and automatic decrement (see the instruction set reference for details).
The Stack is mainly used for storing temporary data, for storing local variables and for storing
return addresses after interrupts and subroutine calls. The Stack Pointer Register always points
to the top of the Stack. Note that the Stack is implemented as growing from higher memory loca-
tions to lower memory locations. This implies that a Stack PUSH command decreases the Stack
Pointer.
The Stack Pointer points to the data SRAM Stack area where the Subroutine and Interrupt
Stacks are located. This Stack space in the data SRAM must be defined by the program before
any subroutine calls are executed or interrupts are enabled. The Stack Pointer must be set to
point above 0x60. The Stack Pointer is decremented by one when data is pushed onto the Stack
with the PUSH instruction, and it is decremented by two when the return address is pushed onto
the Stack with subroutine call or interrupt. The Stack Pointer is incremented by one when data is
popped from the Stack with the POP instruction, and it is incremented by two when data is
popped from the Stack with return from subroutine RET or return from interrupt RETI.
The AVR Stack Pointer is implemented as two 8-bit registers in the I/O space. The number of
bits actually used is implementation dependent. Note that the data space in some implementa-
tions of the AVR architecture is so small that only SPL is needed. In this case, the SPH Register
will not be present.
X-register
Y-register
Z-register
Bit
0x3E
0x3D
Read/Write
Read/Write
Initial Value
Initial Value
The X-, Y-, and Z-registers
RAMEND
RAMEND
SP15
R/W
R/W
SP7
15
7
15
7
R27 (0x1B)
15
7
R29 (0x1D)
15
7
R31 (0x1F)
RAMEND
RAMEND
SP14
SP6
R/W
R/W
14
6
RAMEND
RAMEND
SP13
SP5
R/W
R/W
13
5
ZH
XH
YH
0
RAMEND
RAMEND
SP12
SP4
R/W
R/W
12
4
RAMEND
RAMEND
SP11
SP3
R/W
R/W
11
3
0
0
7
R26 (0x1A)
7
R28 (0x1C)
7
R30 (0x1E)
RAMEND
RAMEND
SP10
SP2
R/W
R/W
10
2
RAMEND
RAMEND
SP9
SP1
R/W
R/W
9
1
XL
YL
ZL
0
RAMEND
RAMEND
R/W
R/W
SP8
SP0
8
0
SPH
SPL
11
0
0
0
0
0