ATMEGA48-20PU Atmel, ATMEGA48-20PU Datasheet - Page 186

• Manufacturer Part Number: ATMEGA48-20PU
• Description: IC AVR MCU 4K 20MHZ 5V 28DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA48-20PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire/SPI/USART/Serial
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Total Internal Ram Size: 512Byte
• # I/os (max): 23
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.8.3
186
ATmega48/88/168
Asynchronous Operational Range
Figure 19-7. Stop Bit Sampling and Next Start Bit Sampling
The same majority voting is done to the stop bit as done for the other bits in the frame. If the stop
bit is registered to have a logic 0 value, the Frame Error (FEn) Flag will be set.
A new high to low transition indicating the start bit of a new frame can come right after the last of
the bits used for majority voting. For Normal Speed mode, the first low level sample can be at
point marked (A) in
(B). (C) marks a stop bit of full length. The early start bit detection influences the operational
range of the Receiver.
The operational range of the Receiver is dependent on the mismatch between the received bit
rate and the internally generated baud rate. If the Transmitter is sending frames at too fast or too
slow bit rates, or the internally generated baud rate of the Receiver does not have a similar (see
Table
bit.
The following equations can be used to calculate the ratio of the incoming data rate and internal
receiver baud rate.
D
S
S
S
R
Table 19-2
that Normal Speed mode has higher toleration of baud rate variations.
F
M
slow
19-2) base frequency, the Receiver will not be able to synchronize the frames to the start
(U2X = 0)
(U2X = 1)
Sample
Sample
RxD
R
and
slow
Sum of character size and parity size (D = 5 to 10 bit)
Samples per bit. S = 16 for Normal Speed mode and S = 8 for Double Speed
mode.
First sample number used for majority voting. S
for Double Speed mode.
Middle sample number used for majority voting. S
S
is the ratio of the slowest incoming data rate that can be accepted in relation to the
receiver baud rate. R
accepted in relation to the receiver baud rate.
M
Table 19-3
=
= 5 for Double Speed mode.
Figure
------------------------------------------ -
S 1
–
1
1
(
D
+
2
+
D S ⋅
19-7. For Double Speed mode the first low level must be delayed to
list the maximum receiver baud rate error that can be tolerated. Note
1
)S
3
2
+
S
4
F
fast
5
3
is the ratio of the fastest incoming data rate that can be
6
7
4
8
STOP 1
9
5
10
(A)
0/1
6
R
0/1
F
fast
= 8 for normal speed and S
M
0/1
0/1
(B)
= 9 for normal speed and
=
-----------------------------------
(
D
(
+
D
1
+
)S
2
)S
+
(C)
S
M
2545S–AVR–07/10
F
= 4