AT89C51RC-24PU Atmel, AT89C51RC-24PU Datasheet - Page 21

IC MCU 32K FLASH 24MHZ 40-DIP

AT89C51RC-24PU

Manufacturer Part Number
AT89C51RC-24PU
Description
IC MCU 32K FLASH 24MHZ 40-DIP
Manufacturer
Atmel
Series
89Cr
Datasheet

Specifications of AT89C51RC-24PU

Core Processor
8051
Core Size
8-Bit
Speed
24MHz
Connectivity
SPI, UART/USART
Peripherals
WDT
Number Of I /o
32
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Cpu Family
89C
Device Core
8051
Device Core Size
8b
Frequency (max)
24MHz
Interface Type
UART
Total Internal Ram Size
512Byte
# I/os (max)
32
Number Of Timers - General Purpose
3
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
4V
Instruction Set Architecture
CISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Through Hole
Pin Count
40
Package Type
PDIP
Processor Series
AT89x
Core
8051
Data Bus Width
8 bit
Data Ram Size
512 B
Maximum Clock Frequency
33 MHz
Number Of Programmable I/os
32
Number Of Timers
3 bit
Operating Supply Voltage
4 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Minimum Operating Temperature
- 40 C
For Use With
AT89STK-11 - KIT STARTER FOR AT89C51RX2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT89C51RC-24PU
Manufacturer:
NICCOMP
Quantity:
40 000
Part Number:
AT89C51RC-24PU
Manufacturer:
ATM
Quantity:
1 980
Part Number:
AT89C51RC-24PU
Quantity:
42
Part Number:
AT89C51RC-24PU
Manufacturer:
MAXIM
Quantity:
100
Part Number:
AT89C51RC-24PU
Manufacturer:
ATMEL
Quantity:
13 649
20. Program Memory Lock Bits
21. Programming the Flash
1920D–MICRO–6/08
The AT89C51RC has three lock bits that can be left unprogrammed (U) or can be programmed
(P) to obtain the additional features listed in
Table 20-1.
When lock bit 1 is programmed, the logic level at the EA pin is sampled and latched during reset.
If the device is powered up without a reset, the latch initializes to a random value and holds that
value until reset is activated. The latched value of EA must agree with the current logic level at
that pin in order for the device to function properly.
The AT89C51RC is shipped with the on-chip Flash memory array ready to be programmed. The
programming interface needs a high-voltage (12-volt) program enable signal and is compatible
with conventional third-party Flash or EPROM programmers.
The AT89C51RC code memory array is programmed byte-by-byte.
Programming Algorithm: Before programming the AT89C51RC, the address, data, and con-
trol signals should be set up according to
AT89C51RC, take the following steps:
1. Input the desired memory location on the address lines.
2. Input the appropriate data byte on the data lines.
3. Activate the correct combination of control signals.
4. Raise EA/V
5. Pulse ALE/PROG once to program a byte in the Flash array or the lock bits. The byte-
1
2
3
4
write cycle is self-timed and typically takes no more than 50 µs. Repeat steps 1
through 5, changing the address and data for the entire array or until the end of the
object file is reached.
Program Lock Bits
LB1
U
P
P
P
Lock Bit Protection Modes
PP
to 12V.
LB2
U
U
P
P
LB3
U
U
U
P
Protection Type
No program lock features
MOVC instructions executed from external program memory
are disabled from fetching code bytes from internal memory,
EA is sampled and latched on reset, and further
programming of the Flash memory is disabled
Same as mode 2, but verify is also disabled
Same as mode 3, but external execution is also disabled
Table 22-1
Table
20-1.
and Figures 22-1 and 22-2. To program the
AT89C51RC
21

Related parts for AT89C51RC-24PU