PIC18F27J13-I/SP Microchip Technology, PIC18F27J13-I/SP Datasheet - Page 410

• Manufacturer Part Number: PIC18F27J13-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J13-I/SP

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Core: PIC
• Processor Series: PIC18F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 48 MHz
• Data Ram Size: 3.76 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 2
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Operating Temperature Range: - 40 C to + 85 C
• A/d Bit Size: 12 bit
• A/d Channels Available: 10
• Height: 3.43 mm
• Interface Type: I2C, SPI, USART
• Length: 34.4 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.15 V
• Width: 7.24 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180030 - BOARD DEMO PIC18F47J13 FS USBMA180029 - BOARD DEMO PIC18F47J53 FS USB
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F47J13 FAMILY
26.9
There are three control registers for the CTMU:
• CTMUCONH
• CTMUCONL
• CTMUICON
REGISTER 26-1:
DS39974A-page 410
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
CTMUEN
R/W-0
Registers
CTMUEN: CTMU Enable bit
1 = Module is enabled
0 = Module is disabled
Unimplemented: Read as ‘0’
CTMUSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
TGEN: Time Generation Enable bit
1 = Enables edge delay generation
0 = Disables edge delay generation
EDGEN: Edge Enable bit
1 = Edges are not blocked
0 = Edges are blocked
EDGSEQEN: Edge Sequence Enable bit
1 = Edge 1 event must occur before Edge 2 event can occur
0 = No edge sequence is needed
IDISSEN: Analog Current Source Control bit
1 = Analog current source output is grounded
0 = Analog current source output is not grounded
CTTRIG: CTMU Special Event Trigger bit
1 = CTMU Special Event Trigger is enabled
0 = CTMU Special Event Trigger is disabled
U-0
—
CTMUCONH: CTMU CONTROL REGISTER HIGH (ACCESS FB3h)
W = Writable bit
‘1’ = Bit is set
CTMUSIDL
R/W-0
R/W-0
TGEN
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
EDGEN
R/W-0
The
(Register 26-1 and Register 26-2) contain control bits
for configuring the CTMU module edge source selec-
tion, edge source polarity selection, edge sequencing,
A/D trigger, analog circuit capacitor discharge and
enables. The CTMUICON register (Register 26-3) has
bits for selecting the current source range and current
source trim.
CTMUCONH
EDGSEQEN
R/W-0
and
 2010 Microchip Technology Inc.
x = Bit is unknown
IDISSEN
R/W-0
CTMUCONL
CTTRIG
R/W-0
registers
bit 0