PIC18F2410-I/ML Microchip Technology, PIC18F2410-I/ML Datasheet - Page 220

• Manufacturer Part Number: PIC18F2410-I/ML
• Description: IC PIC MCU FLASH 8KX16 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2410-I/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• For Use With: XLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

PIC18F2X1X/4X1X
18.8
An A/D conversion can be started by the special event
trigger of the CCP2 module. This requires that the
CCP2M3:CCP2M0 bits (CCP2CON<3:0>) be pro-
grammed as ‘1011’ and that the A/D module is enabled
(ADON bit is set). When the trigger occurs, the GO/
DONE bit will be set, starting the A/D acquisition and
conversion and the Timer1 (or Timer3) counter will be
reset to zero. Timer1 (or Timer3) is reset to automati-
cally repeat the A/D acquisition period with minimal
TABLE 18-2:
DS39636D-page 222
INTCON
PIR1
PIE1
IPR1
PIR2
PIE2
IPR2
ADRESH
ADRESL
ADCON0
ADCON1
ADCON2
PORTA
TRISA
PORTB
TRISB
LATB
PORTE
TRISE
LATE
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion.
Note 1:
Name
(4)
2:
3:
4:
(4)
(4)
Use of the CCP2 Trigger
These bits are unimplemented on 28-pin devices; always maintain these bits clear.
PORTA<7:6> and their direction bits are individually configured as port pins based on various primary
oscillator modes. When disabled, these bits read as ‘0’.
RE3 port bit is available only as an input pin when the MCLRE Configuration bit is ‘0’.
These registers are not implemented on 28-pin devices.
PORTB Data Direction Control Register
PORTB Data Latch Register (Read and Write to Data Latch)
GIE/GIEH PEIE/GIEL TMR0IE
A/D Result Register, High Byte
A/D Result Register, Low Byte
TRISA7
PSPIE
PSPIP
PSPIF
OSCFIF
OSCFIE
OSCFIP
ADFM
RA7
Bit 7
RB7
IBF
—
—
—
—
REGISTERS ASSOCIATED WITH A/D OPERATION
(1)
(1)
(1)
(1)
(2)
TRISA6
RA6
CMIE
CMIP
CMIF
ADIF
ADIE
ADIP
Bit 6
OBF
RB6
—
—
—
—
—
(1)
(2)
PORTA Data Direction Control Register
VCFG1
ACQT2
CHS3
RCIF
RCIE
RCIP
IBOV
Bit 5
RA5
RB5
—
—
—
—
—
PSPMODE
VCFG0
ACQT1
INT0IE
CHS2
TXIE
TXIP
Bit 4
TXIF
RA4
RB4
—
—
—
—
—
PCFG3
ACQT0
SSPIF
SSPIE
SSPIP
BCLIE
BCLIP
RE3
BCLIF
CHS1
software overhead (moving ADRESH:ADRESL to the
desired location). The appropriate analog input
channel must be selected and the minimum acquisition
period is either timed by the user, or an appropriate
T
the GO/DONE bit (starts a conversion).
If the A/D module is not enabled (ADON is cleared), the
special event trigger will be ignored by the A/D module
but will still reset the Timer1 (or Timer3) counter.
RBIE
Bit 3
RA3
RB3
ACQ
—
—
(3)
time selected before the special event trigger sets
PORTE Data Latch Register
TMR0IF
CCP1IF
CCP1IE
CCP1IP
HLVDIF
HLVDIE
HLVDIP
TRISE2
PCFG2
ADCS2
CHS0
Bit 2
RA2
RB2
RE2
GO/DONE
TMR2IF
TMR2IE
TMR2IP
TMR3IF
TMR3IE
TMR3IP
TRISE1
PCFG1
ADCS1
INT0IF
Bit 1
© 2009 Microchip Technology Inc.
RA1
RB1
RE1
TMR1IF
TMR1IE
TMR1IP
CCP2IF
CCP2IE
CCP2IP
TRISE0
PCFG0
ADCS0
ADON
RBIF
Bit 0
RA0
RB0
RE0
on page
Values
Reset
51
54
54
54
54
54
54
53
53
53
53
53
54
54
54
54
54
54
54
54