DSPIC30F1010-30I/SO Microchip Technology, DSPIC30F1010-30I/SO Datasheet - Page 123

• Manufacturer Part Number: DSPIC30F1010-30I/SO
• Description: IC DSPIC MCU/DSP 6K 28SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F1010-30I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 6KB (2K x 24)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240002, DM300023, DM330011
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300023 - KIT DEMO DSPICDEM SMPS BUCKDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.4
The PS PWM module is a very high-speed design that
provides capabilities not found in other PWM genera-
tors. The module supports these PWM modes:
• Standard Edge-Aligned PWM mode
• Complementary PWM mode
• Push-Pull PWM mode
• Multi-Phase PWM mode
• Variable Phase PWM mode
• Current-Limit PWM mode
• Constant Off-time PWM mode
• Current Reset PWM mode
• Independent Time Base PWM mode
12.4.1
Standard Edge-Aligned mode (Figure 12-3) is the basic
PWM mode used by many power converter topologies
such as “Buck”, “Boost” and “Forward”. To create the
edge-aligned PWM, a timer/counter circuit counts
upward from zero to a specified maximum value for the
Period. Another register contains the value for Duty
Cycle, which is constantly compared to the timer
(Period) value. While the timer/counter value is less
than or equal to the duty cycle value, the PWM output
signal is asserted. When the timer value exceeds the
duty cycle value, the PWM signal is deasserted. When
the timer is greater than the period value, the timer is
reset, and the process repeats.
FIGURE 12-3:
© 2006 Microchip Technology Inc.
Period
Value
PWMH
0
Module Functionality
Timer
Value
STANDARD EDGE-ALIGNED PWM
MODE
Duty Cycle Match
Duty Cycle
Period
EDGE-ALIGNED PWM
Timer Resets
Preliminary
12.4.2
Complementary PWM is generated in a manner similar
to standard Edge-Aligned PWM. Complementary mode
provides a second PWM output signal on the PWML
pin that is the complement of the primary PWM signal
(PWMH). Complementary mode PWM is shown in
Figure 12-4.
FIGURE 12-4:
12.4.3
The Push-Pull mode shown in Figure 12-5 is a version
of the standard Edge-Aligned PWM mode where the
active PWM signal is alternately outputted on one of
two PWM pins. There is no complementary PWM out-
put available. This mode is useful in transformer-based
power converters. Transformer-based circuits must
avoid any direct currents that will cause their cores to
saturate. The Push-Pull mode ensures that the duty
cycle of the two phases is identical, thus yielding a net
DC bias of zero.
FIGURE 12-5:
Period
Value
Period
Value
dsPIC30F1010/202X
PWMH
PWML
PWMH
PWML
0
0
Duty Cycle Match
Duty Cycle Match
Duty Cycle
Timer
Value
Timer
Value
COMPLEMENTARY PWM MODE
PUSH-PULL PWM MODE
Duty Cycle
Period
Period
COMPLEMENTARY PWM
PUSH-PULL PWM
Timer Resets
Timer Resets
(Period)-(Duty Cycle)
Duty Cycle
DS70178C-page 121