DSPIC30F1010-30I/SO Microchip Technology, DSPIC30F1010-30I/SO Datasheet - Page 22

• Manufacturer Part Number: DSPIC30F1010-30I/SO
• Description: IC DSPIC MCU/DSP 6K 28SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F1010-30I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 6KB (2K x 24)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240002, DM300023, DM330011
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300023 - KIT DEMO DSPICDEM SMPS BUCKDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

dsPIC30F1010/202X
2.2
The programmer’s model is shown in Figure 2-1 and
consists of 16x16-bit working registers (W0 through
W15), 2x40-bit accumulators (ACCA and ACCB),
STATUS register (SR), Data Table Page register
(TBLPAG), Program Space Visibility Page register
(PSVPAG), DO and REPEAT registers (DOSTART,
DOEND, DCOUNT and RCOUNT), and Program
Counter (PC). The working registers can act as data,
address or offset registers. All registers are memory
mapped. W0 acts as the W register for file register
addressing.
Some of these registers have a shadow register asso-
ciated with each of them, as shown in Figure 2-1. The
shadow register is used as a temporary holding register
and can transfer its contents to or from its host register
upon the occurrence of an event. None of the shadow
registers are accessible directly. The following rules
apply for transfer of registers into and out of shadows.
• PUSH.S and POP.S
• DO instruction
When a byte operation is performed on a working reg-
ister, only the Least Significant Byte (LSB) of the target
register is affected. However, a benefit of memory
mapped working registers is that both the Least and
Most Significant Bytes (MSBs) can be manipulated
through byte wide data memory space accesses.
DS70178C-page 20
W0, W1, W2, W3, SR (DC, N, OV, Z and C bits
only) are transferred.
DOSTART, DOEND, DCOUNT shadows are
pushed on loop start, and popped on loop end.
Programmer’s Model
Preliminary
2.2.1
The dsPIC
W15 is the dedicated software Stack Pointer (SP), and
will be automatically modified by exception processing
and subroutine calls and returns. However, W15 can be
referenced by any instruction in the same manner as all
other W registers. This simplifies the reading, writing
and manipulation of the Stack Pointer (e.g., creating
stack frames).
W15 is initialized to 0x0800 during a Reset. The user
may reprogram the SP during initialization to any
location within data space.
W14 has been dedicated as a Stack Frame Pointer as
defined by the LNK and ULNK instructions. However,
W14 can be referenced by any instruction in the same
manner as all other W registers.
2.2.2
The dsPIC DSC core has a 16-bit STATUS Register
(SR), the LSB of which is referred to as the SR Low
Byte (SRL) and the MSB as the SR High Byte (SRH).
See Figure 2-1 for SR layout.
SRL contains all the MCU ALU operation status flags
(including the Z bit), as well as the CPU Interrupt Prior-
ity Level Status bits, IPL<2:0>, and the REPEAT active
Status bit, RA. During exception processing, SRL is
concatenated with the MSB of the PC to form a
complete word value, which is then stacked.
The upper byte of the STATUS register contains the
DSP Adder/Subtracter status bits, the DO Loop Active
bit (DA) and the Digit Carry (DC) Status bit.
2.2.3
The Program Counter is 23 bits wide. Bit 0 is always
clear. Therefore, the PC can address up to 4M
instruction words.
Note:
®
SOFTWARE STACK POINTER/
FRAME POINTER
In order to protect against misaligned
stack accesses, W15<0> is always clear.
STATUS REGISTER
PROGRAM COUNTER
DSC devices contain a software stack.
© 2006 Microchip Technology Inc.