DSPIC33FJ16GS502-I/SO Microchip Technology, DSPIC33FJ16GS502-I/SO Datasheet - Page 219

• Manufacturer Part Number: DSPIC33FJ16GS502-I/SO
• Description: IC DSPIC MCU/DSP 16K 28-SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16GS502-I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Core Frequency: 40MHz
• Core Supply Voltage: 3.3V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 21
• Flash Memory Size: 16KB
• Supply Voltage Range: 3V To 3.6V
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

16.0
The Serial Peripheral Interface (SPI) module is a
synchronous serial interface useful for communicating
with other peripheral or microcontroller devices. These
peripheral devices can be serial EEPROMs, shift
registers, display drivers, analog-to-digital converters
and so on. The SPI module is compatible with SPI and
SIOP from Motorola
FIGURE 16-1:
© 2009 Microchip Technology Inc.
Note:
SDOx
SCKx
SDIx
SSx
SERIAL PERIPHERAL
INTERFACE (SPI)
This data sheet summarizes the features
of
dsPIC33FJ16GSX02/X04
devices. It is not intended to be a
comprehensive reference source.
complement the information in this data
sheet, refer to the “dsPIC33F Family
Reference Manual”, Section 18. “Serial
Peripheral Interface (SPI)” (DS70206),
which is available on the Microchip
web site (www.microchip.com).
Read SPIxBUF
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
the
Control
Sync
®
Transfer
.
dsPIC33FJ06GS101/X02
SPI MODULE BLOCK DIAGRAM
SPIxRXB
bit 0
SPIxBUF
SPIxSR
Control
Clock
Shift Control
SPIxTXB
families
Transfer
Write SPIxBUF
and
Preliminary
To
of
Select
Edge
The SPI module consists of a 16-bit shift register,
SPIxSR (where x = 1), used for shifting data in and out,
and a buffer register, SPIxBUF. A control register,
SPIxCON, configures the module. Additionally, a status
register, SPIxSTAT, indicates status conditions.
The serial interface consists of the following four pins:
• SDIx (Serial Data Input)
• SDOx (Serial Data Output)
• SCKx (Shift Clock Input Or Output)
• SSx (Active-Low Slave Select).
In Master mode operation, SCK is a clock output; in
Slave mode, it is a clock input.
16
Secondary
1:1 to 1:8
Prescaler
Internal Data Bus
1:1/4/16/64
Prescaler
Primary
F
SPIxCON1<1:0>
SPIxCON1<4:2>
Enable
Master Clock
DS70318D-page 217
CY