DSPIC33FJ16GS502-I/SO Microchip Technology, DSPIC33FJ16GS502-I/SO Datasheet - Page 236

• Manufacturer Part Number: DSPIC33FJ16GS502-I/SO
• Description: IC DSPIC MCU/DSP 16K 28-SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16GS502-I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Core Frequency: 40MHz
• Core Supply Voltage: 3.3V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 21
• Flash Memory Size: 16KB
• Supply Voltage Range: 3V To 3.6V
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 18-2:
DS70318D-page 234
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15,13
bit 14
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7-6
UTXISEL1
Note 1: Refer to Section 17. “UART” (DS70188) in the “dsPIC33F Family Reference Manual” for information on
R/W-0
R/W-0
URXISEL<1:0>
enabling the UART module for transmit operation.
UTXISEL<1:0>: Transmission Interrupt Mode Selection bits
11 = Reserved; do not use
10 = Interrupt when a character is transferred to the Transmit Shift register, and as a result, the
01 = Interrupt when the last character is shifted out of the Transmit Shift register; all transmit
00 = Interrupt when a character is transferred to the Transmit Shift register (this implies there is at
UTXINV: Transmit Polarity Inversion bit
If IREN = 0:
1 = UxTX Idle state is ‘0’
0 = UxTX Idle state is ‘1’
If IREN = 1:
1 = IrDA
0 = IrDA
Unimplemented: Read as ‘0’
UTXBRK: Transmit Break bit
1 = Send Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit;
0 = Sync Break transmission disabled or completed
UTXEN: Transmit Enable bit
1 = Transmit enabled, UxTX pin controlled by UARTx
0 = Transmit disabled, any pending transmission is aborted and buffer is reset; UxTX pin controlled
UTXBF: Transmit Buffer Full Status bit (read-only)
1 = Transmit buffer is full
0 = Transmit buffer is not full; at least one more character can be written
TRMT: Transmit Shift Register Empty bit (read-only)
1 = Transmit Shift register is empty and transmit buffer is empty (the last transmission has completed)
0 = Transmit Shift register is not empty, a transmission is in progress or queued
URXISEL<1:0>: Receive Interrupt Mode Selection bits
11 = Interrupt is set on UxRSR transfer making the receive buffer full (i.e., has 4 data characters)
10 = Interrupt is set on UxRSR transfer making the receive buffer 3/4 full (i.e., has 3 data characters)
0x = Interrupt is set when any character is received and transferred from the UxRSR to the receive
UTXINV
R/W-0
R/W-0
cleared by hardware upon completion
by port
U
transmit buffer becomes empty
operations are completed
least one character open in the transmit buffer)
buffer; receive buffer has one or more characters
x
®
®
STA: UART
encoded UxTX Idle state is ‘1’
encoded UxTX Idle state is ‘0’
HC = Hardware Clearable bit
W = Writable bit
‘1’ = Bit is set
UTXISEL0
ADDEN
R/W-0
R/W-0
x
STATUS AND CONTROL REGISTER
(1)
Preliminary
RIDLE
U-0
R-1
—
C = Clearable bit
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0, HC
UTXBRK
PERR
R-0
UTXEN
R/W-0
FERR
R-0
(1)
© 2009 Microchip Technology Inc.
x = Bit is unknown
UTXBF
OERR
R/C-0
R-0
URXDA
TRMT
R-1
R-0
bit 8
bit 0