PIC24HJ64GP502-E/MM Microchip Technology, PIC24HJ64GP502-E/MM Datasheet - Page 62

IC PIC MCU FLASH 64K 28-QFN

PIC24HJ64GP502-E/MM

Manufacturer Part Number
PIC24HJ64GP502-E/MM
Description
IC PIC MCU FLASH 64K 28-QFN
Manufacturer
Microchip Technology
Series
PIC® 24Hr

Specifications of PIC24HJ64GP502-E/MM

Program Memory Type
FLASH
Program Memory Size
64KB (22K x 24)
Package / Case
28-QFN
Core Processor
PIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
21
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Processor Series
PIC24HJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
8 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
21
Number Of Timers
5
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM300027
Minimum Operating Temperature
- 40 C
On-chip Adc
10-ch x 10-bit or 10-ch x 12-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164336 - MODULE SOCKET FOR PM3 28/44QFN
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
APPENDIX B:
This silicon errata issue was previously published in the
following documents, which are available from the
Microchip web site:
• dsPIC33FJXXXGPX06/X08/X10 Rev. A2 Silicon
• dsPIC33FJXXXMCX06/X08/X10 Rev. A2 Silicon
• PIC24HJXXXGPX06/X08/X10 Rev. A2 Silicon
This issue is included in this document to further assist
customers.
DS70152H-page 62
Errata (DS80306)
Errata (DS80307)
Errata (DS80280)
DEVICE ID REGISTER
SILICON ERRATA
ADDENDUM
1. Module: Device ID Register
On a few devices, the content of the Device ID
register can change from the factory programmed
default value immediately after RTSP or ICSP™
Flash programming.
As a result, development tools will not recognize
these devices and will generate an error message
indicating that the device ID and the device part
number
peripherals will be reconfigured and will not
function as described in the device data sheet.
Refer to Section 5. “Flash Programming”
(DS70191), of the “dsPIC33F Family Reference
Manual” for an explanation of RTSP and ICSP
Flash programming.
Work around
All RTSP and ICSP Flash programming routines
must be modified as follows:
1. No word programming is allowed. Any word
2. During row programming, load write latches as
3. After latches are loaded, reload any latch
4. Start
5. After row programming is complete, verify the
6. If Flash verification errors are found, repeat
Steps 1 through 5 in the work around are
implemented in MPLAB
MPLAB ICD 2, MPLAB REAL ICE™ in-circuit
emulator and MPLAB PM3 tools.
programming must be replaced with row
programming.
described in 5.4.2.3 “Loading Write Latches”
of
(DS70191).
location (in a given row) that has 5 LSB set to
0x18, with the original data. For example,
reload one of the following latch locations with
the desired data:
0xXXXX18, 0xXXXX38, 0xXXXX58,
0xXXXX78, 0xXXXX98, 0xXXXXB8,
0xXXXXD8, 0xXXXXF8
NVMOP<3:0> = ‘0001’ (Memory row program
operation) in the NVMCON register.
contents of Flash memory.
steps 2 through 5. If Flash verification errors
are found after a second iteration, report this
problem to Microchip.
Section
do
row
not
5.
© 2010 Microchip Technology Inc.
programming
match.
®
“Flash
IDE version 7.61 for the
Additionally,
Programming”
by
setting
some

Related parts for PIC24HJ64GP502-E/MM