DSPIC30F4011-20I/P Microchip Technology, DSPIC30F4011-20I/P Datasheet - Page 115
![IC DSPIC MCU/DSP 48K 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
DSPIC30F4011-20I/P
Manufacturer Part Number
DSPIC30F4011-20I/P
Description
IC DSPIC MCU/DSP 48K 40DIP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20IP.pdf
(26 pages)
2.DSPIC30F4012-30ISO.pdf
(238 pages)
3.DSPIC30F4012-30ISO.pdf
(18 pages)
4.DSPIC30F4012-30ISO.pdf
(6 pages)
5.DSPIC30F4012-30ISO.pdf
(16 pages)
6.DSPIC30F4012-30ISO.pdf
(22 pages)
Specifications of DSPIC30F4011-20I/P
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
30
Program Memory Size
48KB (16K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 9x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Core Frequency
40MHz
Core Supply Voltage
5.5V
Embedded Interface Type
CAN, I2C, SPI, UART
No. Of I/o's
30
Flash Memory Size
48KB
Supply Voltage Range
2.5V To 5.5V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC30F003 - MODULE SOCKET DSPIC30F 40DIPACICE0206 - ADAPTER MPLABICE 40P 600 MIL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
DSPIC30F4011-20IP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DSPIC30F4011-20I/P
Manufacturer:
MICROCHI
Quantity:
20 000
Company:
Part Number:
DSPIC30F4011-20I/PT
Manufacturer:
MSC
Quantity:
32
Company:
Part Number:
DSPIC30F4011-20I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
17.2
The I2CADD register contains the Slave mode
addresses. The register is a 10-bit register.
If the A10M bit (I2CCON<10>) is ‘0’, the address is
interpreted by the module as a 7-bit address. When an
address is received, it is compared to the 7 LSbs of the
I2CADD register.
If the A10M bit is ‘1’, the address is assumed to be a
10-bit address. When an address is received, it will be
compared with the binary value, ‘11110
(where A9 and A8 are two Most Significant bits of
I2CADD). If that value matches, the next address will
be compared with the Least Significant 8 bits of
I2CADD, as specified in the 10-bit addressing protocol.
The 7-bit I
dsPIC30F are shown in
TABLE 17-1:
17.3
Once enabled (I2CEN = 1), the slave module will wait
for a Start bit to occur (i.e., the I
Following the detection of a Start bit, 8 bits are shifted
into I2CRSR and the address is compared against
I2CADD. In 7-bit mode (A10M = 0), I2CADD<6:0> bits
are compared against I2CRSR<7:1>, and I2CRSR<0>
is the R_W bit. All incoming bits are sampled on the
rising edge of SCL.
If an address match occurs, an Acknowledgement will
be sent, and the Slave Event Interrupt Flag (SI2CIF) is
set on the falling edge of the ninth (ACK) bit. The
address match does not affect the contents of the
I2CRCV buffer or the RBF bit.
17.3.1
If the R_W bit received is a ‘1’, then the serial port will
go into Transmit mode. It will send ACK on the ninth bit
and then hold SCL to ‘0’ until the CPU responds by writ-
ing to I2CTRN. SCL is released by setting the SCLREL
bit and 8 bits of data are shifted out. Data bits are
shifted out on the falling edge of SCL, such that SDA is
valid during SCL high (see timing diagram). The inter-
rupt pulse is sent on the falling edge of the ninth clock
pulse, regardless of the status of the ACK received
from the master.
© 2010 Microchip Technology Inc.
0x00
0x01-0x03
0x04-0x07
0x08-0x77
0x78-0x7B
0x7C-0x7F
Address
I
I
2
2
C Module Addresses
C 7-bit Slave Mode Operation
SLAVE TRANSMISSION
2
C slave addresses supported by the
General call address or Start byte
Reserved
HS mode master codes
Valid 7-bit addresses
Valid 10-bit addresses (lower 7 bits)
Reserved
7-BIT I
ADDRESSES
Table
2
C™ SLAVE
Description
17-1.
2
C module is ‘Idle’).
A9
A8’
17.3.2
If the R_W bit received is a ‘0’ during an address
match, then Receive mode is initiated. Incoming bits
are sampled on the rising edge of SCL. After 8 bits are
received, if I2CRCV is not full or I2COV is not set,
I2CRSR is transferred to I2CRCV. ACK is sent on the
ninth clock.
If the RBF flag is set, indicating that I2CRCV is still
holding data from a previous operation (RBF = 1), then
ACK is not sent; however, the interrupt pulse is gener-
ated. In the case of an overflow, the contents of the
I2CRSR are not loaded into the I2CRCV.
17.4
In 10-bit mode, the basic receive and transmit
operations are the same as in the 7-bit mode. However,
the criteria for address match is more complex.
The I
addressed for a write operation, with two address bytes
following a Start bit.
The A10M bit is a control bit that signifies that the
address in I2CADD is a 10-bit address rather than a
7-bit address. The address detection protocol for the
first byte of a message address is identical for 7-bit
and 10-bit messages but the bits being compared are
different.
I2CADD holds the entire 10-bit address. Upon receiv-
ing an address following a Start bit, I2CRSR<7:3> is
compared against a literal ‘11110’ (the default 10-bit
address) and I2CRSR<2:1> are compared against
I2CADD<9:8>. If a match occurs and if R_W = 0, the
interrupt pulse is sent. The ADD10 bit will be cleared to
indicate a partial address match. If a match fails or
R_W = 1, the ADD10 bit is cleared and the module
returns to the Idle state.
The low byte of the address is then received and com-
pared with I2CADD<7:0>. If an address match occurs,
the interrupt pulse is generated and the ADD10 bit is
set, indicating a complete 10-bit address match. If an
address match did not occur, the ADD10 bit is cleared
and the module returns to the Idle state.
Note:
dsPIC30F4011/4012
2
C specification dictates that a slave must be
I
2
C 10-bit Slave Mode Operation
SLAVE RECEPTION
The I2CRCV will be loaded if the I2COV
bit = 1 and the RBF flag = 0. In this case,
a read of the I2CRCV was performed but
the user did not clear the state of the
I2COV bit before the next receive
occurred. The Acknowledgement is not
sent (ACK = 1) and the I2CRCV is
updated.
DS70135G-page 115