DSPIC33FJ128MC506A-I/MR Microchip Technology, DSPIC33FJ128MC506A-I/MR Datasheet - Page 75

• Manufacturer Part Number: DSPIC33FJ128MC506A-I/MR
• Description: IC DSPIC MCU/DSP 128K 64-QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC506A-I/MR

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Product: DSCs
• Processor Series: DSPIC33F
• Core: dsPIC
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.0
The dsPIC33FJXXXMCX06A/X08A/X10A devices con-
tain internal Flash program memory for storing and
executing application code. The memory is readable,
writable and erasable during normal operation over the
entire V
Flash memory can be programmed in two ways:
1.
2.
ICSP allows a dsPIC33FJXXXMCX06A/X08A/X10A
device to be serially programmed while in the end
application circuit. This is simply done with two lines for
programming clock and programming data (one of the
alternate programming pin pairs: PGECx/PGEDx), and
three other lines for power (V
FIGURE 5-1:
 2009 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
In-Circuit Serial Programming™ (ICSP™)
programming capability
Run-Time Self-Programming (RTSP)
DD
2: Some registers and associated bits
FLASH PROGRAM MEMORY
range.
of the dsPIC33FJXXXMCX06A/X08A/
X10A family of devices. However, it is not
intended to be a comprehensive refer-
ence source. To complement the informa-
tion in this data sheet, refer to Section 5.
“Flash Programming” (DS70191) in the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
described in this section may not be avail-
able on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
Using
Program Counter
Using
Table Instruction
User/Configuration
Space Select
ADDRESSING FOR TABLE REGISTERS
dsPIC33FJXXXMCX06A/X08A/X10A
DD
), ground (V
1/0
0
TBLPAG Reg
8 Bits
SS
) and
Preliminary
Program Counter
24-Bit EA
24 Bits
Master Clear (MCLR). This allows customers to
manufacture boards with unprogrammed devices and
then program the digital signal controller just before
shipping the product. This also allows the most recent
firmware or a custom firmware to be programmed.
RTSP is accomplished using TBLRD (table read) and
TBLWT (table write) instructions. With RTSP, the user
can write program memory data by blocks (or ‘rows’) of
64 instructions (192 bytes) at a time or by single
program memory word; the user can erase program
memory in blocks or ‘pages’ of 512 instructions
(1536 bytes) at a time.
5.1
Regardless of the method used, all programming of
Flash memory is done with the table read and table
write instructions. These allow direct read and write
access to the program memory space from the data
memory while the device is in normal operating mode.
The 24-bit target address in the program memory is
formed using bits<7:0> of the TBLPAG register and the
Effective Address (EA) from a W register specified in
the table instruction, as shown in Figure 5-1.
The TBLRDL and TBLWTL instructions are used to read
or write to bits<15:0> of program memory. TBLRDL and
TBLWTL can access program memory in both Word
and Byte modes.
The TBLRDH and TBLWTH instructions are used to read
or write to bits<23:16> of program memory. TBLRDH
and TBLWTH can also access program memory in Word
or Byte mode.
Working Reg EA
16 Bits
Table Instructions and Flash
Programming
0
Byte
Select
DS70594B-page 75