AT89C5132-ROTUL Atmel, AT89C5132-ROTUL Datasheet - Page 47
![IC 8051 MCU FLASH 64K USB 80TQFP](/photos/12/13/121358/313-80-tqfp_sml.jpg)
AT89C5132-ROTUL
Manufacturer Part Number
AT89C5132-ROTUL
Description
IC 8051 MCU FLASH 64K USB 80TQFP
Manufacturer
Atmel
Series
AT89C513xr
Specifications of AT89C5132-ROTUL
Core Processor
C52X2
Core Size
8-Bit
Speed
20MHz
Connectivity
IDE/ATAPI, I²C, MMC, PCM, SPI, UART/USART, USB
Peripherals
I²S, POR, WDT
Number Of I /o
44
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
2.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.3 V
Data Converters
A/D 2x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
80-TQFP, 80-VQFP
Cpu Family
89C
Device Core
8051
Device Core Size
8b
Frequency (max)
40MHz
Interface Type
IDE/SPI/UART/USB
Total Internal Ram Size
2.25KB
# I/os (max)
44
Number Of Timers - General Purpose
2
Operating Supply Voltage (typ)
3V
Operating Supply Voltage (max)
3.3V
Operating Supply Voltage (min)
2.7V
On-chip Adc
2-chx10-bit
Instruction Set Architecture
CISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
80
Package Type
TQFP
Package
80TQFP
Family Name
89C
Maximum Speed
40 MHz
Operating Supply Voltage
3 V
Data Bus Width
8 Bit
Number Of Programmable I/os
44
Number Of Timers
2
Maximum Clock Frequency
20 MHz
Data Ram Size
2304 B
Mounting Style
SMD/SMT
A/d Bit Size
10 bit
A/d Channels Available
2
Height
1.45 mm
Length
14.1 mm
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Supply Voltage (max)
3.3 V
Supply Voltage (min)
2.7 V
Width
14.1 mm
For Use With
AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCU
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
11.4.1
11.4.2
Figure 11-3. Power-down Exit Waveform Using INT1:0
Figure 11-4. Power-down Exit Waveform Using KIN3:0
Note:
4173E–USB–09/07
1. KIN3:0 can be high or low-level triggered.
Entering Power-down Mode
Exiting Power-down Mode
KIN3:0
INT1:0
OSC
OSC
1
To enter Power-down mode, set PD bit in PCON register. The AT89C5132 enters the Power-
down mode upon execution of the instruction that sets PD bit. The instruction that sets PD bit is
the last instruction executed.
If V
restored to the normal operating level.
There are 2 ways to exit the Power-down mode:
1. Generate an enabled external interrupt.
Note:
2. Generate a reset.
Active phase
Active phase
DD
–
was reduced during the Power-down mode, do not exit Power-down mode until V
1. The external interrupt used to exit Power-down mode must be configured as level sensitive
2. Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM
The AT89C5132 provides capability to exit from Power-down using INT0, INT1, and
KIN3:0 inputs. In addition, using KIN input provides high or low level exit capability
(see Section “Keyboard Interface”, page 181).
Hardware clears PD bit in PCON register which starts the oscillator and restores the
clocks to the CPU and peripherals. Using INTn input, execution resumes when the
input is released (see Figure 11-3) while using KINx input, execution resumes after
counting 1024 clock ensuring the oscillator is restarted properly (see Figure 11-4).
This behavior is necessary for decoding the key while it is still pressed. In both
cases, execution resumes with the interrupt service routine. Upon completion of the
interrupt service routine, program execution resumes with the instruction
immediately following the instruction that activated Power-down mode.
(
interrupt must be long enough to allow the oscillator to stabilize. The execution will only
resume when the interrupt is deasserted.
content.
INT0
and
Power-down Phase
Power-down
INT1
) and must be assigned the highest priority. In addition, the duration of the
1024 clock count
Oscillator Restart
Active phase
Active Phase
AT89C5132
DD
47
is