AT32UC3A0256-ALUT Atmel, AT32UC3A0256-ALUT Datasheet - Page 526

• Manufacturer Part Number: AT32UC3A0256-ALUT
• Description: IC MCU AVR32 256KB FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3A0256-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 109
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: 2-Wire, RS-485, SPI, USART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL, KSK-EVK1100-PL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATEXTWIFI, ATEVK1100, ATEVK1105
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AT32UC3A
• No. Of I/o's: 109
• Ram Memory Size: 64KB
• Cpu Speed: 66MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Package: 144LQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 66 MHz
• Operating Supply Voltage: 1.8|3.3 V
• For Use With: ATEVK1105 - KIT EVAL FOR AT32UC3A0ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1100 - KIT DEV/EVAL FOR AVR32 AT32UC3A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 30-25. Example of an IN Pipe with 1 Data Bank
Figure 30-26. Example of an IN Pipe with 2 Data Banks
30.7.3.11
32058J–AVR32–04/11
RXINI
FIFOCON
IN
Management of OUT Pipes
RXINI
FIFOCON
(bank 0)
IN
DATA
OUT packets are sent by the host. All the data can be written by the firmware which acknowl-
edges or not the bank when it is full.
The pipe must be configured and unfrozen first.
The TXOUTI bit is set by hardware at the same time as FIFOCON when the current bank is free.
This triggers a PXINT interrupt if TXOUTE = 1.
TXOUTI shall be cleared by software (by setting the TXOUTIC bit) to acknowledge the interrupt,
what has no effect on the pipe FIFO.
The firmware then writes into the FIFO and clears the FIFOCON bit to allow the USB controller
to send the data. If the OUT pipe is composed of multiple banks, this also switches to the next
bank. The TXOUTI and FIFOCON bits are updated by hardware in accordance with the status of
the next bank.
TXOUTI shall always be cleared before clearing FIFOCON.
The RWALL bit is set by hardware when the current bank is not full, i.e. the software can write
further data into the FIFO.
Note that if the firmware decides to switch to the Suspend state (by clearing the SOFE bit) while
a bank is ready to be sent, the USB controller automatically exits this state and the bank is sent.
(bank 0)
DATA
HW
ACK
SW
read data from CPU
HW
ACK
BANK 0
SW
read data from CPU
IN
BANK 0
SW
(bank 1)
IN
DATA
SW
(bank 0)
DATA
HW
ACK
read data from CPU
SW
HW
ACK
BANK 1
read data from CPU
AT32UC3A
SW
BANK 0
526