STM8S207C8T6 STMicroelectronics, STM8S207C8T6 Datasheet - Page 55

• Manufacturer Part Number: STM8S207C8T6
• Description: MCU 8BIT 64K MEMORY 48-LQFP
• Manufacturer: STMicroelectronics
• Series: STM8Sr

Specifications of STM8S207C8T6

• Mfg Application Notes: STM8S Getting Started
• Core Processor: STM8
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1.5K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.95 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Controller Family/series: STM8
• No. Of I/o's: 38
• Eeprom Memory Size: 1.5KB
• Ram Memory Size: 4KB
• Cpu Speed: 24MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Processor Series: STM8S20x
• Core: STM8
• Data Bus Width: 8 bit
• Data Ram Size: 6 KB
• Interface Type: CAN, 12C, SPI, UART
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 2
• Operating Supply Voltage: 2.95 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWSTM8
• Development Tools By Supplier: STICE-SYS001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: 497-10032 - EVAL KIT MOTOR CONTROL STM8S497-10031 - EVAL KIT TOUCH SENSING STM8S497-10592 - BOARD DAUGHTER FOR STM8S207/8497-10593 - KIT STARTER FOR STM8S207/8 SER497-8506 - BOARD EVAL FOR STM8S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8951; STM8S207C8T6

STM8S207xx, STM8S208xx
10.2
Absolute maximum ratings
Stresses above those listed as ‘absolute maximum ratings’ may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 15.
1. All power (V
2. I
|V
|V
V
Symbol
DDx
DDx
SSx
external power supply
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
there is no positive injection current, and the corresponding V
INJ(PIN)
V
V
ESD
IN
- V
- V
- V
DD
SS
SS
must never be exceeded. This is implicitly insured if V
| Variations between all the different ground pins
| Variations between different power pins
Voltage characteristics
DD
Supply voltage (including V
Input voltage on true open drain pins (PE1, PE2)
Input voltage on any other pin
Electrostatic discharge voltage
, V
DDIO
, V
IN
DDA
>V
DD
) and ground (V
while a negative injection is induced by V
Doc ID 14733 Rev 11
Ratings
DDA and
SS
(2)
, V
SSIO
V
DDIO
, V
SSA
)
(1)
) pins must always be connected to the
IN
IN
maximum must always be respected
maximum is respected. If V
(2)
IN
see
sensitivity) on page 88
V
V
<V
INJ(PIN)
SS
SS
Min
-0.3
ratings (electrical
SS
Electrical characteristics
Absolute maximum
- 0.3
- 0.3
. For true open-drain pads,
value. A positive
V
DD
Max
6.5
6.5
IN
50
50
+ 0.3
maximum
55/105
Unit
mV
V