STM32F103CBT6 STMicroelectronics, STM32F103CBT6 Datasheet - Page 35

• Manufacturer Part Number: STM32F103CBT6
• Description: MCU ARM 128K FLASH/TIMER
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103CBT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: STM32F103x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 20 KB
• Interface Type: CAN/I2C/SPI/USART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10-ch x 12-bit)
• Controller Family/series: (ARM Cortex) STM32
• No. Of I/o's: 37
• Ram Memory Size: 20KB
• Cpu Speed: 72MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 12
• Rohs Compliant: Yes
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Total Internal Ram Size: 20KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6288

STM32F103x8, STM32F103xB
5.1.7
5.2
Current consumption measurement
Figure 14. Current consumption measurement scheme
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 7: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 6.
1. All main power (V
2. I
|V
V
V
supply, in the permitted range.
maximum is respected. If V
externally to the I
induced by V
Symbol
SSX
INJ(PIN)
|V
ESD(HBM)
DD
V
–V
DDx
IN
V
SS
must never be exceeded (see
|
SS
|
Voltage characteristics
IN
External main supply voltage (including V
and V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different V
Variations between all the different ground pins
Electrostatic discharge voltage (human body
model)
< V
characteristics, and
INJ(PIN)
DD
SS
, V
DD
.
DDA
)
value. A positive injection is induced by V
(1)
) and ground (V
IN
maximum cannot be respected, the injection current must be limited
Doc ID 13587 Rev 12
Ratings
Table 7: Current
Table 8: Thermal characteristics
I DD _V BAT
SS
, V
I DD
SSA
(2)
DD
) pins must always be connected to the external power
V DD
power pins
V DDA
V BAT
(2)
characteristics). This is implicitly insured if V
DDA
Table 6: Voltage
IN
ai14126
> V
see
Absolute maximum ratings
(electrical sensitivity)
IN
V
V
max while a negative injection is
SS
SS
Section 5.3.11:
–0.3
Min
Electrical characteristics
 0.3
0.3
may cause permanent
characteristics,
V
DD
Max
+5.5
4.0
50
50
+0.3
IN
Unit
35/96
mV
V