MC908GZ60CFJE Freescale Semiconductor, MC908GZ60CFJE Datasheet - Page 131

• Manufacturer Part Number: MC908GZ60CFJE
• Description: IC MCU 60K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ60CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 11
Low-Voltage Inhibit (LVI)
11.1 Introduction
This section describes the low-voltage inhibit (LVI) module, which monitors the voltage on the V
and can force a reset when the V
11.2 Features
Features of the LVI module include:
11.3 Functional Description
Figure 11-1
contains a bandgap reference circuit and comparator. Clearing the LVI power disable bit, LVIPWRD,
enables the LVI to monitor V
module to generate a reset when V
bit, LVISTOP, enables the LVI to operate in stop mode. Setting the LVI 5-V or 3-V trip point bit, LVI5OR3,
enables the trip point voltage, V
enables the trip point voltage, V
in
Freescale Semiconductor
Chapter 21 Electrical
•
•
•
Programmable LVI reset
Selectable LVI trip voltage
Programmable stop mode operation
shows the structure of the LVI module. The LVI is enabled out of reset. The LVI module
After a power-on reset (POR) the LVI’s default mode of operation is 3 V. If
a 5-V system is used, the user must set the LVI5OR3 bit to raise the trip
point to 5-V operation. Note that this must be done after every power-on
reset since the default will revert back to 3-V mode after each power-on
reset. If the V
3-V mode trip voltage when POR is released, the part will operate because
V
taken to ensure that V
released.
If the user requires 5-V mode and sets the LVI5OR3 bit after a power-on
reset while the V
microcontroller unit (MCU) will immediately go into reset. The LVI in this
case will hold the part in reset until either V
point, V
V which will re-trigger the power-on reset and reset the trip point to 3-V
operation.
TRIPF
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 Data Sheet, Rev. 6
defaults to 3-V mode after a POR. So, in a 5-V system care must be
TRIPR
Specifications.
, which will release reset or V
DD
DD
TRIPF
supply is below the 5-V mode trip voltage but above the
DD
TRIPF
voltage. Clearing the LVI reset disable bit, LVIRSTD, enables the LVI
DD
supply is not above the V
DD
, to be configured for 3-V operation. The actual trip points are shown
voltage falls below the LVI trip falling voltage, V
, to be configured for 5-V operation. Clearing the LVI5OR3 bit
DD
falls below a voltage, V
is above the 5-V mode trip voltage after POR is
NOTE
DD
DD
decreases to approximately 0
goes above the rising 5-V trip
TRIPR
TRIPF
for 5-V mode, the
. Setting the LVI enable in stop mode
TRIPF
.
DD
pin
131