MC908GZ60CFJE Freescale Semiconductor, MC908GZ60CFJE Datasheet - Page 261

• Manufacturer Part Number: MC908GZ60CFJE
• Description: IC MCU 60K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ60CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

As an example, a 4.9152 MHz crystal, with the TMBCLKSEL set for divide-by-128 and the TBR2–TBR0
set to {011}, the divider is 16,384 and the interrupt rate calculates to:
17.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby modes.
17.6.1 Wait Mode
The timebase module remains active after execution of the WAIT instruction. In wait mode the timebase
register is not accessible by the CPU.
If the timebase functions are not required during wait mode, reduce the power consumption by stopping
the timebase before executing the WAIT instruction.
17.6.2 Stop Mode
The timebase module may remain active after execution of the STOP instruction if the oscillator has been
enabled to operate during stop mode through the OSCENINSTOP bit in the configuration register. The
timebase module can be used in this mode to generate a periodic wakeup from stop mode.
If the oscillator has not been enabled to operate in stop mode, the timebase module will not be active
during stop mode. In stop mode, the timebase register is not accessible by the CPU.
If the timebase functions are not required during stop mode, reduce power consumption by disabling the
timebase module before executing the STOP instruction.
Freescale Semiconductor
4.9152 x 10
Do not change TBR2–TBR0 bits while the timebase is enabled (TBON = 1).
16,384
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 Data Sheet, Rev. 6
TBR2
6
0
0
0
0
1
1
1
1
= 3.33 ms
Table 17-1. Timebase Divider Selection
TBR1
0
0
1
1
0
0
1
1
TBR0
0
1
0
1
0
1
0
1
NOTE
32,768
8192
2048
128
64
32
16
0
8
TMBCLKSEL
Divider
4,194,304
1,048,576
262144
16,384
8192
4096
2048
1024
1
Low-Power Modes
261