MC908GZ60CFJE Freescale Semiconductor, MC908GZ60CFJE Datasheet - Page 310

• Manufacturer Part Number: MC908GZ60CFJE
• Description: IC MCU 60K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ60CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Development Support
20.3.1.4 Data Format
Communication with the monitor ROM is in standard non-return-to-zero (NRZ) mark/space data format.
Transmit and receive baud rates must be identical.
20.3.1.5 Break Signal
A start bit (0) followed by nine 0 bits is a break signal. When the monitor receives a break signal, it drives
the PTA0 pin high for the duration of approximately two bits and then echoes back the break signal.
20.3.1.6 Baud Rate
The communication baud rate is controlled by the crystal frequency or external clock and the state of the
PTB4 pin (when IRQ is set to V
on IRQ and the reset vector blank, then the baud rate is independent of PTB4.
Table 20-1
effective baud rate is the bus frequency divided by 278. If using a crystal as the clock source, be aware
of the upper frequency limit that the internal clock module can handle. See
or
20.3.1.7 Commands
The monitor ROM firmware uses these commands:
The monitor ROM firmware echoes each received byte back to the PTA0 pin for error checking. An 11-bit
delay at the end of each command allows the host to send a break character to cancel the command. A
delay of two bit times occurs before each echo and before READ, IREAD, or READSP data is returned.
The data returned by a read command appears after the echo of the last byte of the command.
310
21.8 3.3-Volt Control Timing
•
•
•
•
•
•
READ (read memory)
WRITE (write memory)
IREAD (indexed read)
IWRITE (indexed write)
READSP (read stack pointer)
RUN (run user program)
also lists external frequencies required to achieve a standard baud rate of 7200 bps. The
Wait one bit time after each echo before sending the next byte.
START
BIT
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 Data Sheet, Rev. 6
0
BIT 0
1
2
BIT 1
TST
for this limit.
MISSING STOP BIT
3
Figure 20-12. Monitor Data Format
) upon entry into monitor mode. If monitor mode was entered with V
Figure 20-13. Break Transaction
4
BIT 2
5
6
BIT 3
7
BIT 4
NOTE
BIT 5
APPROXIMATELY 2 BITS DELAY
BEFORE ZERO ECHO
BIT 6
0
1
BIT 7
2
3
STOP
BIT
4
21.7 5.0-Volt Control Timing
START
NEXT
5
BIT
6
Freescale Semiconductor
7
DD