MC908AP64CFAE Freescale Semiconductor, MC908AP64CFAE Datasheet - Page 177

• Manufacturer Part Number: MC908AP64CFAE
• Description: IC MCU 64K 8MHZ SPI 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08AP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908AP64E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• Package: 48LQFP
• Family Name: HC08
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

11.8.5 SCI Status Register 2
SCI status register 2 contains flags to signal the following conditions:
BKF — Break Flag Bit
RPF — Reception in Progress Flag Bit
11.8.6 SCI Data Register
The SCI data register (SCDR) is the buffer between the internal data bus and the receive and transmit
shift registers. Reset has no effect on data in the SCI data register.
R7/T7–R0/T0 — Receive/Transmit Data Bits
Freescale Semiconductor
•
•
This clearable, read-only bit is set when the SCI detects a break character on the RxD pin. In SCS1,
the FE and SCRF bits are also set. In 9-bit character transmissions, the R8 bit in SCC3 is cleared. BKF
does not generate a CPU interrupt request. Clear BKF by reading SCS2 with BKF set and then reading
the SCDR. Once cleared, BKF can become set again only after logic 1s again appear on the RxD pin
followed by another break character. Reset clears the BKF bit.
This read-only bit is set when the receiver detects a logic 0 during the RT1 time period of the start bit
search. RPF does not generate an interrupt request. RPF is reset after the receiver detects false start
bits (usually from noise or a baud rate mismatch) or when the receiver detects an idle character. Polling
RPF before disabling the SCI module or entering stop mode can show whether a reception is in
progress.
Reading the SCDR accesses the read-only received data bits, R7–R0. Writing to the SCDR writes the
data to be transmitted, T7–T0. Reset has no effect on the SCDR.
1 = Break character detected
0 = No break character detected
1 = Reception in progress
0 = No reception in progress
Break character detected
Incoming data
Address:
Address:
Do not use read/modify/write instructions on the SCI data register.
Reset:
Reset:
Read:
Read:
Write:
Write:
$0017
$0018
Bit 7
Bit 7
R7
T7
0
Figure 11-14. SCI Status Register 2 (SCS2)
= Unimplemented
Figure 11-15. SCI Data Register (SCDR)
R6
T6
6
0
6
MC68HC908AP Family Data Sheet, Rev. 4
R5
T5
5
0
5
NOTE
Unaffected by reset
R4
T4
4
0
4
R3
T3
3
0
3
R2
T2
2
0
2
BKF
R1
T1
1
0
1
Bit 0
RPF
Bit 0
R0
T0
0
I/O Registers
177