MC908AP64CFAE Freescale Semiconductor, MC908AP64CFAE Datasheet - Page 196

• Manufacturer Part Number: MC908AP64CFAE
• Description: IC MCU 64K 8MHZ SPI 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08AP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908AP64E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• Package: 48LQFP
• Family Name: HC08
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Infrared Serial Communications Interface Module (IRSCI)
12.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby modes.
12.6.1 Wait Mode
The SCI module remains active after the execution of a WAIT instruction. In wait mode, the SCI module
registers are not accessible by the CPU. Any enabled CPU interrupt request from the SCI module can
bring the MCU out of wait mode.
If SCI module functions are not required during wait mode, reduce power consumption by disabling the
module before executing the WAIT instruction.
Refer to
12.6.2 Stop Mode
The SCI module is inactive after the execution of a STOP instruction. The STOP instruction does not
affect SCI register states. SCI module operation resumes after an external interrupt.
Because the internal clock is inactive during stop mode, entering stop mode during an SCI transmission
or reception results in invalid data.
Refer to
12.7 SCI During Break Module Interrupts
The system integration module (SIM) controls whether status bits in other modules can be cleared during
interrupts generated by the break module. The BCFE bit in the SIM break flag control register (SBFCR)
enables software to clear status bits during the break state.
To allow software to clear status bits during a break interrupt, write a logic 1 to the BCFE bit. If a status
bit is cleared during the break state, it remains cleared when the MCU exits the break state.
To protect status bits during the break state, write a logic 0 to the BCFE bit. With BCFE at logic 0 (its
default state), software can read and write I/O registers during the break state without affecting status bits.
Some status bits have a two-step read/write clearing procedure. If software does the first step on such a
bit before the break, the bit cannot change during the break state as long as BCFE is at logic 0. After the
break, doing the second step clears the status bit.
12.8 I/O Signals
The two IRSCI I/O pins are:
196
•
•
•
•
Framing error (FE) — The FE bit in IRSCS1 is set when a logic 0 occurs where the receiver expects
a stop bit. The framing error interrupt enable bit, FEIE, in IRSCC3 enables FE to generate SCI error
CPU interrupt requests.
Parity error (PE) — The PE bit in IRSCS1 is set when the SCI detects a parity error in incoming
data. The parity error interrupt enable bit, PEIE, in IRSCC3 enables PE to generate SCI error CPU
interrupt requests.
PTC6/SCTxD — Transmit data
PTC7/SCRxD — Receive data
7.6 Low-Power Modes
7.6 Low-Power Modes
for information on exiting wait mode.
for information on exiting stop mode.
MC68HC908AP Family Data Sheet, Rev. 4
Freescale Semiconductor