MC908AP64CFAE Freescale Semiconductor, MC908AP64CFAE Datasheet - Page 306

• Manufacturer Part Number: MC908AP64CFAE
• Description: IC MCU 64K 8MHZ SPI 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08AP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908AP64E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• Package: 48LQFP
• Family Name: HC08
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Electrical Specifications
22.10 3V Control Timing
304
Pullup resistors
Low-voltage inhibit, trip falling voltage1
Low-voltage inhibit, trip rising voltage1
Low-voltage inhibit, trip voltage2
V
Internal operating frequency
RST input pulse width low
1. V
2. Typical values reflect average measurements at midpoint of voltage range, 25 °C only.
3. At V
4. Run (operating) I
5. Wait I
6. STOP I
7. STOP I
8. Maximum is highest voltage that POR is guaranteed. The rearm voltage is triggered by V
9. If minimum V
10. R
11. Values are not affected by operating V
12. Measured from V
1. V
2. Some modules may require a minimum frequency greater than dc for proper operation; see appropriate table for this in-
3. Minimum pulse width reset is guaranteed to be recognized. It is possible for a smaller pulse width to cause a reset.
REG
PTD[0:7]
RST, IRQ1, IRQ2
than the I
than 100 pF on all outputs; C
measured with all modules enabled.
on all outputs. C
V
formation.
DD
DD
DD
(10), (12)
PU1
DD
= 2.7 to 3.3 Vdc, V
is reached.
= 2.7 to 3.3 Vdc, V
DD
and R
DD
DD
= 3V, an on-chip charge pump is activated for the V
measured using external 16MHz/32MHz clock to OSC1; all inputs 0.2 V from rail; no dc loads; less than 100 pF
DD
measured with external 32.768kHz clock to OSC1; no port pins sourcing current.
measured with OSC1 grounded; no port pins sourcing current.
(10)
values at V
DD
PU2
is not reached before the internal POR reset is released,
L
are measured at V
DD
Characteristic
= 20 pF on OSC2; all ports configured as inputs; OSC2 capacitance linearly affects wait I
DD
measured using external 16MHz/32MHz clock to OSC1; all inputs 0.2 V from rail; no dc loads; less
= V
Characteristic
(3)
SS
SS
DD
TRIPF1
(2)
= 0 Vdc; timing shown with respect to 20% V
= 0 Vdc, T
= 5V.
L
(10)
Table 22-8. DC Electrical Characteristics (3V)
= 20 pF on OSC2; all ports configured as inputs; OSC2 capacitance linearly affects run I
(Min) to 5.5 V.
(1)
DD
(10)
(11)
A
MC68HC908AP Family Data Sheet, Rev. 4
(1)
= 5.0V
= T
Table 22-9. Control Timing (3V)
DD
L
; they are the same for 3V and 5V.
to T
H
, unless otherwise noted.
Symbol
V
V
V
REG
V
R
R
TRIPR1
TRIPF1
TRIPF2
REG
PU1
PU2
regulator, therefore some I
Symbol
DD
RST
t
f
IRL
OP
and 70% V
2.25
2.35
2.25
2.25
Min
21
21
must be driven low externally until minimum
DD
Min
750
—
, unless otherwise noted.
REG
Typ
2.45
2.55
2.45
2.50
27
27
DD
.
(2)
values will appear higher
Freescale Semiconductor
Max
—
8
Max
2.65
2.75
2.65
2.75
39
39
DD
.
MHz
Unit
ns
Unit
kΩ
kΩ
V
V
V
V
DD
;