MC9S12E128CPVE Freescale Semiconductor, MC9S12E128CPVE Datasheet - Page 369

• Manufacturer Part Number: MC9S12E128CPVE
• Description: IC MCU 128K FLASH 25MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E128CPVE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12E
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 92
• Number Of Timers: 12
• Operating Supply Voltage: 3.135 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• On-chip Dac: 2-ch x 8-bit
• Controller Family/series: HCS12/S12X
• No. Of I/o's: 90
• Ram Memory Size: 8KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

When initially enabled by setting the PWMEN bit, no current status has previously been sampled. PWM
value registers one, three, and five initially control the three PWM pairs when configured for current status
correction.
11.4.5.4
Output polarity of the PWMs is determined by two options: TOPNEG and BOTNEG. The top polarity
option, TOPNEG, controls the polarity of PWM0, PWM2 and PWM4. The bottom polarity option,
BOTNEG, controls the polarity of PWM1, PWM3 and PWM5. Positive polarity means when the PWM is
active its output is high. Conversely, negative polarity means when the PWM is active its output is low.
The TOPNEG and BOTNEG are in the configure register. TOPNEG is the output of PWM0, PWM2 and
PWM4. They are active low. If TOPNEG is set, PWM0, PWM2, and PWM4 outputs become active-low.
When BOTNEG is set, PWM1, PWM3, and PWM5 outputs are active-low. When these bits are clear, their
respective PWM pins are active-high. See
Freescale Semiconductor
Output Polarity
Values latched on the ISx pins are buffered so only one PWM register is
used per PWM cycle. If a current status changes during a PWM period, the
new value does not take effect until the next PWM period.
DESIRED LOAD VOLTAGE
DESIRED LOAD VOLTAGE
LOAD VOLTAGE
LOAD VOLTAGE
BOTTOM PWM
BOTTOM PWM
Figure 11-60. Correction with Negative Current
Figure 11-59. Correction with Positive Current
TOP PWM
TOP PWM
MC9S12E128 Data Sheet, Rev. 1.07
Figure 11-59
Chapter 11 Pulse Width Modulator with Fault Protection (PMF15B6CV2)
NOTE
and
Figure
11-60.
369