MC9S12XDT256CAA Freescale Semiconductor, MC9S12XDT256CAA Datasheet - Page 553

• Manufacturer Part Number: MC9S12XDT256CAA
• Description: IC MCU 256K FLASH 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XDT256CAA

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 59
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Processor Series: S12XD
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 59
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12XDP512E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

is set, an interrupt service is requested whenever the corresponding time-out flag PTF in the PIT time-out
flag (PITTF) register is set. The flag can be cleared by writing a one to the flag bit.
13.4.3
The PIT module contains four hardware trigger signal lines PITTRIG[3:0], one for each timer channel.
These signals can be connected on SoC level to peripheral modules enabling e.g. periodic ATD conversion
(please refer to the SoC Guide for the mapping of PITTRIG[3:0] signals to peripheral modules).
Whenever a timer channel time-out is reached, the corresponding PTF flag is set and the corresponding
trigger signal PITTRIG triggers a rising edge. The trigger feature requires a minimum time-out period of
two bus clock cycles because the trigger is asserted high for at least one bus clock cycle. For load register
values PITLD = 0x0001 and PITMTLD = 0x0002 the flag setting, trigger timing and a restart with force
load is shown in
13.5
13.5.1
Set the configuration registers before the PITE bit in the PITCFLMT register is set. Before PITE is set, the
configuration registers can be written in arbitrary order.
13.5.2
When the PITCE register bits, the PITINTE register bits or the PITE bit in the PITCFLMT register are
cleared, the corresponding PIT interrupt flags are cleared. In case of a pending PIT interrupt request, a
spurious interrupt can be generated. Two strategies, which avoid spurious interrupts, are recommended:
13.5.3
A flag is cleared by writing a one to the flag bit. Always use store or move instructions to write a one in
certain bit positions. Do not use the BSET instructions. Do not use any C-constructs that compile to BSET
instructions. “BSET flag_register, #mask” must not be used for flag clearing because BSET is a
read-modify-write instruction which writes back the “bit-wise or” of the flag_register and the mask into
the flag_register. BSET would clear all flag bits that were set, independent from the mask.
For example, to clear flag bit 0 use: MOVB #$01,PITTF.
Freescale Semiconductor
1. Reset the PIT interrupt flags only in an ISR. When entering the ISR, the I mask bit in the CCR is
2. After setting the I mask bit with the SEI instruction, the PIT interrupt flags can be cleared. Then
set automatically. The I mask bit must not be cleared before the PIT interrupt flags are cleared.
clear the I mask bit with the CLI instruction to re-enable interrupts.
Initialization/Application Information
Hardware Trigger
Startup
Shutdown
Flag Clearing
Be careful when resetting the PITE, PINTE or PITCE bits in case of pending
PIT interrupt requests, to avoid spurious interrupt requests.
Figure
13-20.
MC9S12XDP512 Data Sheet, Rev. 2.21
NOTE
Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1)
553