C8051F021-GQ Silicon Laboratories Inc, C8051F021-GQ Datasheet - Page 191

IC 8051 MCU 64K FLASH 64TQFP

C8051F021-GQ

Manufacturer Part Number
C8051F021-GQ
Description
IC 8051 MCU 64K FLASH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Datasheets

Specifications of C8051F021-GQ

Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
64-TQFP, 64-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
32
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
4.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
32
Number Of Timers
4
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F020DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 8-bit or 8-ch x 12-bit
On-chip Dac
2-ch x 12-bit
No. Of I/o's
32
Ram Memory Size
4352Byte
Cpu Speed
25MHz
No. Of Timers
5
No. Of Pwm Channels
5
Rohs Compliant
Yes
Data Rom Size
64 KB
A/d Bit Size
12 bit
A/d Channels Available
8
Height
1.05 mm
Length
10 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Width
10 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1200 - DEV KIT FOR F020/F021/F022/F023
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1201
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
BUSY
Bit7
R
BUSY: Busy Status Flag.
0: SMBus0 is free
1: SMBus0 is busy
ENSMB: SMBus Enable.
This bit enables/disables the SMBus serial interface.
0: SMBus0 disabled.
1: SMBus0 enabled.
STA: SMBus Start Flag.
0: No START condition is transmitted.
1: When operating as a master, a START condition is transmitted if the bus is free. (If the bus is not
free, the START is transmitted after a STOP is received.) If STA is set after one or more bytes have
been transmitted or received and before a STOP is received, a repeated START condition is transmit-
ted. To ensure proper operation, the STO bit should be explicitly cleared to ‘0’ before setting the STA
bit to ‘1’.
STO: SMBus Stop Flag.
0: No STOP condition is transmitted.
1: Setting STO to logic 1 causes a STOP condition to be transmitted. When a STOP condition is
received, hardware clears STO to logic 0. If both STA and STO are set, a STOP condition is transmit-
ted followed by a START condition. In slave mode, setting the STO flag causes SMBus to behave as
if a STOP condition was received.
SI: SMBus Serial Interrupt Flag.
This bit is set by hardware when one of 27 possible SMBus0 states is entered. (Status code 0xF8 does
not cause SI to be set.) When the SI interrupt is enabled, setting this bit causes the CPU to vector to
the SMBus interrupt service routine. This bit is not automatically cleared by hardware and must be
cleared by software.
AA: SMBus Assert Acknowledge Flag.
This bit defines the type of acknowledge returned during the acknowledge cycle on the SCL line.
0: A "not acknowledge" (high level on SDA) is returned during the acknowledge cycle.
1: An "acknowledge" (low level on SDA) is returned during the acknowledge cycle.
FTE: SMBus Free Timer Enable Bit
0: No timeout when SCL is high
1: Timeout when SCL high time exceeds limit specified by the SMB0CR value.
TOE: SMBus Timeout Enable Bit
0: No timeout when SCL is low.
ENSMB
R/W
Bit6
Figure 18.8. SMB0CN: SMBus0 Control Register
STA
R/W
Bit5
STO
R/W
Bit4
R/W
Bit3
SI
Rev. 1.4
R/W
AA
Bit2
C8051F020/1/2/3
FTE
R/W
Bit1
(bit addressable)
TOE
R/W
Bit0
SFR Address:
00000000
Reset Value
0xC0
191

Related parts for C8051F021-GQ