M30626FJPGP#U3C Renesas Electronics America, M30626FJPGP#U3C Datasheet - Page 166

• Manufacturer Part Number: M30626FJPGP#U3C
• Description: IC M16C MCU FLASH 512K 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30626FJPGP#U3C

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: I²C, IEBus, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 31K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PR0K33062PS001BE - R0K33062P STARTER KITR0K33062PS000BE - KIT EVAL STARTER FOR M16C/62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/62P Group (M16C/62P, M16C/62PT)
Rev.2.41
REJ09B0185-0241
Figure 15.10
Timer A2 Mode Register (i=2 to 4)
(when using two-phase pulse signal processing)
b7 b6 b5 b4
NOTES :
1.
2.
0 1
TCK1 bit is valid for Timer A3 mode register. No matter how this bit is set, Timer A2 and A4 alw ays operate in normal
processing mode and x4 processing mode, respectively.
If tw o-phase pulse signal processing is desired, follow ing register settings are required:
• Set the TAiP bit in the UDF register to “1” (tw o-phase pulse signal processing function enabled).
• Set the TAiTGH and TAiTGL bits in the TRGSR register to “00b” (TAiIN pin input).
• Set the port direction bits for TAiIN and TAiOUT to “0” (input mode).
Jan 10, 2006
b3
0 0 0 1
b2 b1 b0
TA2MR to TA4MR Registers in Event Counter Mode (when using two-phase pulse
signal processing with Timer A2, A3 and A4)
Bit Symbol
TMOD0
TMOD1
TA2MR to TA4MR
TCK0
TCK1
MR0
MR1
MR2
MR3
Page 149 of 390
Symbol
Operation Mode Select Bit
To use tw o-phase pulse signal processing, set this bit to “0”.
To use tw o-phase pulse signal processing, set this bit to “0”.
To use tw o-phase pulse signal processing, set this bit to “1”.
To use tw o-phase pulse signal processing, set this bit to “0”.
Count Operation Type Select Bit
Tw o-phase pulse signal processing
Operation Type Select Bit
Bit Name
0398h to 039Ah
Address
(1, 2)
b1 b0
0 1 : Event counter mode
0 : Reload type
1 : Free-run type
0 : Normal processing operation
1 : Multiply-by-4 processing operation
After Reset
Function
00h
15. Timers
RW
RW
RW
RW
RW
RW
RW
RW
RW