M30626FJPGP#U3C Renesas Electronics America, M30626FJPGP#U3C Datasheet - Page 57

• Manufacturer Part Number: M30626FJPGP#U3C
• Description: IC M16C MCU FLASH 512K 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30626FJPGP#U3C

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: I²C, IEBus, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 31K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PR0K33062PS001BE - R0K33062P STARTER KITR0K33062PS000BE - KIT EVAL STARTER FOR M16C/62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/62P Group (M16C/62P, M16C/62PT)
Rev.2.41
REJ09B0185-0241
5.
Hardware reset 1, brown-out detection reset (hardware reset 2), software reset, watchdog timer reset and oscillation
stop detection reset are available to reset the microcomputer.
5.1
Figure 5.1
5.1.1
5.1.2
The microcomputer resets pins, the CPU and SFR by setting the RESET pin. If the supply voltage meets the
recommended operating conditions, the microcomputer resets all pins when an “L” signal is applied to the RESET
pin (see Table 5.1 Pin Status When RESET Pin Level is “L”). The oscillation circuit is also reset and the main
clock starts oscillation. The microcomputer resets the CPU and SFR when the signal applied to the RESET pin
changes low (“L”) to high (“H”). The microcomputer executes the program in an address indicated by the reset
vector. The internal RAM is not reset. When an “L” signal is applied to the RESET pin while writing data to the
internal RAM, the internal RAM is in an indeterminate state.
Figure 5.1 shows an Example Reset Circuit. Figure 5.2 shows a Reset Sequence. Table 5.1 lists Pin Status When
RESET Pin Level is “L”. Figure 5.3 shows CPU Register Status After Reset. Refer to 4. Special Function
Register (SFR) for SFR states after reset.
Reset
RESET
Hardware Reset 1
(1) Apply “L” to the RESET pin
(2) Apply 20 or more clock cycles to the XIN pin
(3) Apply an “H” signal to the RESET pin
(1) Apply “L” to the RESET pin
(2) Raise the supply voltage to the recommended operating level
(3) Insert td(P-R) ms as wait time for the internal voltage to stabilize
(4) Apply 20 or more clock cycles to the XIN pin
(5) Apply “H” to the RESET pin
NOTES:
Jan 10, 2006
Reset on a Stable Supply Voltage
Power-on Reset
1. If VCC1>VCC2, the VCC2 voltage must be lower than that of VCC1 when the power
Example Reset Circuit
is being turned on or off.
VCC1
Page 40 of 390
VCC1
RESET
0V
0V
Recommended
operation voltage
0.2VCC1
or below
0.2VCC1 or below
Supply a clock with td(P-R) + 20
or more cycles to the XIN pin
5. Reset