PIC16C774-I/L Microchip Technology, PIC16C774-I/L Datasheet - Page 125
![IC MCU OTP 4KX14 A/D PWM 44PLCC](/photos/6/63/66325/150-44-plcc_sml.jpg)
PIC16C774-I/L
Manufacturer Part Number
PIC16C774-I/L
Description
IC MCU OTP 4KX14 A/D PWM 44PLCC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16C773SO.pdf
(201 pages)
3.PIC16C774P.pdf
(13 pages)
4.PIC16C774P.pdf
(16 pages)
Specifications of PIC16C774-I/L
Core Size
8-Bit
Program Memory Size
7KB (4K x 14)
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Number Of I /o
33
Program Memory Type
OTP
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 10x12b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Controller Family/series
PIC16C
No. Of I/o's
33
Ram Memory Size
256Byte
Cpu Speed
20MHz
No. Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164309 - MODULE SKT FOR PM3 44PLCCISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING444-1001 - DEMO BOARD FOR PICMICRO MCUDVA16XL441 - ADAPTER DEVICE ICE 44PLCC309-1040 - ADAPTER 44-PLCC ZIF TO 40-DIP309-1039 - ADAPTER 44-PLCC TO 40-DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
PIC16C774-04I/L
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16C774-I/L
Manufacturer:
Microchip Technology
Quantity:
10 000
11.7
An A/D conversion can be started by the “special event
trigger” of the CCP module. This requires that the
CCPnM<3:0> bits be programmed as 1011b and that
the A/D module is enabled (ADON is set). When the
trigger occurs, the GO/DONE bit will be set on Q2 to
start the A/D conversion and the Timer1 counter will
be reset to zero. Timer1 is reset to automatically
repeat the A/D conversion cycle, with minimal software
overhead (moving the ADRESH and ADRESL to the
desired location). The appropriate analog input chan-
nel must be selected before the “special event trigger”
sets the GO/DONE bit (starts a conversion cycle).
If the A/D module is not enabled (ADON is cleared),
then the “special event trigger” will be ignored by the
A/D module, but will still reset the Timer1 counter.
11.8
A device reset forces all registers to their reset state.
This forces the A/D module to be turned off, and any
conversion is aborted. The value that is in the
ADRESH and ADRESL registers are not modified.
The ADRESH and ADRESL registers will contain
unknown data after a Power-on Reset.
1999 Microchip Technology Inc.
Use of the CCP Trigger
Effects of a RESET
Advance Information
11.9
Not all applications require a result with 12-bits of res-
olution, but may instead require a faster conversion
time. The A/D module allows users to make the
trade-off of conversion speed to resolution. Regard-
less of the resolution required, the acquisition time is
the same. To speed up the conversion, the A/D mod-
ule may be halted by clearing the GO/DONE bit after
the desired number of bits in the result have been con-
verted. Once the GO/DONE bit has been cleared, all
of the remaining A/D result bits are ‘0’. The equation
to determine the time before the GO/DONE bit can be
switched is as follows:
Since T
must use some method (a timer, software loop, etc.) to
determine when the A/D GO/DONE bit may be
cleared. Table 11-2 shows a comparison of time
required for a conversion with 4-bits of resolution, ver-
sus the normal 12-bit resolution conversion. The
example is for devices operating at 20 MHz. The A/D
clock is programmed for 32 T
TABLE 11-2
Tosc
T
1T
AD
AD
Where: N = number of bits of resolution required,
and 1T
Conversion time = N•T
= 32 Tosc
+N•T
AD
Faster Conversion - Lower
Resolution Trade-off
AD
AD
is based from the device oscillator, the user
is the amplifier settling time.
4-BIT vs. 12-BIT
CONVERSION TIMES
PIC16C77X
AD
OSC
+ 1T
Freq.
(MHz)
20
20
20
.
AD
DS30275A-page 125
50 ns
1.6 s
8 s
4-bit
Resolution
50 ns
1.6 s
20.8 s
12-bit