AT91SAM9M10-CU Atmel, AT91SAM9M10-CU Datasheet - Page 847

• Manufacturer Part Number: AT91SAM9M10-CU
• Description: IC MCU 16/32BIT ARM9 324TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9M10-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 400MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 1.1 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 133 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 2 x 16 bit
• Operating Supply Voltage: 1.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9M10-G45-EK
• Controller Family/series: AT91
• No. Of I/o's: 160
• Ram Memory Size: 64KB
• Cpu Speed: 400MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Cpu Family: AT91
• Device Core: ARM926EJ-S
• Device Core Size: 32b
• Frequency (max): 400MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 160
• Number Of Timers - General Purpose: 7
• Operating Supply Voltage (typ): 1.8/2.5/3.3V
• Operating Supply Voltage (max): 1.1/1.95/3.6V
• Operating Supply Voltage (min): 0.9/1.65/1.8/3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 324
• Package Type: TFBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

38.5.12.7
38.5.12.8
38.5.12.9
847
AT91SAM9M10
Entering Suspend State (Bus Activity)
Receiving a Host Resume
Sending an External Resume
When a Suspend (no bus activity on the USB bus) is detected, the DET_SUSPD signal in the
UDPHS_STA register is set. This triggers an interrupt if the corresponding bit is set in the
UDPHS_IEN register. This flag is cleared by writing to the UDPHS_CLRINT register. Then the
device enters Suspend Mode.
In this state bus powered devices must drain less than 500 μA from the 5V VBUS. As an exam-
ple, the microcontroller switches to slow clock, disables the PLL and main oscillator, and goes
into Idle Mode. It may also switch off other devices on the board.
The UDPHS device peripheral clocks can be switched off. Resume event is asynchronously
detected.
In Suspend mode, a resume event on the USB bus line is detected asynchronously, transceiver
and clocks disabled (however the pull-up should not be removed).
Once the resume is detected on the bus, the signal WAKE_UP in the UDPHS_INTSTA is set. It
may generate an interrupt if the corresponding bit in the UDPHS_IEN register is set. This inter-
rupt may be used to wake-up the core, enable PLL and main oscillators and configure clocks.
In Suspend State it is possible to wake-up the host by sending an external resume.
The device waits at least 5 ms after being entered in Suspend State before sending an external
resume.
The device must force a K state from 1 to 15 ms to resume the host.
6355B–ATARM–21-Jun-10