MC908QY8CDWE Freescale Semiconductor, MC908QY8CDWE Datasheet - Page 45

• Manufacturer Part Number: MC908QY8CDWE
• Description: IC MCU 8BIT 8K FLASH 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QY8CDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Processor Series: HC08QY
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

break, the bit cannot change during the break state as long as BCFE is cleared. After the break, doing the
second step clears the status bit.
3.7 I/O Signals
The ADC10 module shares its pins with general-purpose input/output (I/O) port pins. See
port location of these shared pins. The ADC10 on this MCU uses V
pins. This MCU does not have an external trigger source.
3.7.1 ADC10 Analog Power Pin (V
The ADC10 analog portion uses V
to V
may be necessary to ensure clean V
3.7.2 ADC10 Analog Ground Pin (V
The ADC10 analog portion uses V
to V
In cases where separate power supplies are used for analog and digital power, the ground connection
between these supplies should be at the V
these supplies if possible. The V
3.7.3 ADC10 Voltage Reference High Pin (V
V
V
potential as V
the V
AC current in the form of current spikes required to supply charge to the capacitor array at each
successive approximation step is drawn through the V
to meet this current demand is a 0.1 μF capacitor with good high frequency characteristics. This capacitor
is connected between V
Resistance in the path is not recommended because the current will cause a voltage drop which could
result in conversion errors. Inductance in this path must be minimum (parasitic only).
3.7.4 ADC10 Voltage Reference Low Pin (V
V
V
potential as V
Freescale Semiconductor
REFH
REFH
REFL
REFL
DD
SS
DDA
. If externally available, connect the V
. If externally available, connect the V
is the power supply for setting the low-reference voltage for the converter. In some packages,
is connected internally to V
is the power supply for setting the high-reference voltage for the converter. In some packages,
is connected internally to V
potential (V
DDA
SSA
If externally available, route V
and place bypass capacitors as near as possible to the package.
Route V
capacitors as near as possible to the package.
. There will be a brief current associated with V
, or may be driven by an external source that is between the minimum V
REFH
REFH
REFH
must never exceed V
carefully for maximum noise immunity and place bypass
and V
SSA
SSA
SSA
DDA
DDA
REFL
MC68HC908QB8 Data Sheet, Rev. 3
DDA
pin makes a good single point ground location.
. If externally available, connect the V
. If externally available, V
as its ground pin. In some packages, V
as its power pin. In some packages, V
DDA
and must be placed as close as possible to the package pins.
for good results.
SSA
SSA
DDA
SSA
)
DDA
)
pin. This should be the only ground connection between
pin to the same voltage potential as V
DDA
pin to the same voltage potential as V
NOTE
NOTE
carefully for maximum noise immunity
REFL
REFH
).
REFH
)
)
and V
REFH
REFL
REFL
DD
and V
may be connected to the same
loop. The best external component
when the sampling capacitor is
SS
REFL
DDA
SSA
as its supply and reference
pin to the same voltage
is connected internally
is connected internally
DD
SS
. External filtering
.
Figure 3-1
DDA
I/O Signals
spec and
for
45