MC908LJ24CPBE Freescale Semiconductor, MC908LJ24CPBE Datasheet - Page 180

• Manufacturer Part Number: MC908LJ24CPBE
• Description: IC MCU 24K FLASH 8MHZ SPI 64LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908LJ24CPBE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SPI
• Peripherals: LCD, LVD, POR, PWM
• Number Of I /o: 40
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: HC08LJ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V, 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68EML08LJLKE, ZK-HC08LX-A, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit
• Controller Family/series: HC08
• No. Of I/o's: 40
• Ram Memory Size: 768Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Monitor ROM (MON)
Data Sheet
180
The control and data bytes are described below.
•
•
•
•
Figure 10-9. Data Block Format for ROM-Resident Routines
Bus speed — This one byte indicates the operating bus speed of
the MCU. The value of this byte should be equal to 4 times the bus
speed. E.g., for a 4MHz bus, the value is 16 ($10). This control
byte is useful where the MCU clock source is switched between
the PLL clock and the crystal clock.
Data size — This one byte indicates the number of bytes in the
data array that are to be manipulated. The maximum data array
size is 255. Routines EE_WRITE and EE_READ are restricted to
manipulate a data array between 2 to 15 bytes. Whereas routines
ERARNGE and MON_ERARNGE do not manipulate a data array,
thus, this data size byte has no meaning.
Start address — These two bytes, high byte followed by low byte,
indicate the start address of the FLASH memory to be
manipulated.
Data array — This data array contains data that are to be
manipulated. Data in this array are programmed to FLASH
memory by the programming routines: PRGRNGE,
MON_PRGRNGE, EE_WRITE. For the read routines: LDRNGE,
MON_LDRNGE, and EE_READ, data is read from FLASH and
stored in this array.
ADDRESS AS POINTER
FILE_PTR
Monitor ROM (MON)
ARRAY
DATA
$XXXX
START ADDRESS HIGH (ADDRH)
START ADDRESS LOW (ADDRL)
BUS SPEED (BUS_SPD)
DATA SIZE (DATASIZE)
R
DATA N
DATA 0
DATA 1
A
MC68HC908LJ24/LK24 — Rev. 2.1
M
Freescale Semiconductor
BLOCK
DATA