MPC562MZP56 Freescale Semiconductor, MPC562MZP56 Datasheet - Page 142

• Manufacturer Part Number: MPC562MZP56
• Description: IC MPU 32BIT 56MHZ PPC 388-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC562MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 64
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Processor Series: MPC5xx
• Core: PowerPC
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: SCI, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 22
• Operating Supply Voltage: 2.6 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 32 Channel)
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No

Signal Descriptions
2-44
1
2
3
4
5
6
7
8
9
10
11
IRAMSTBY
Signal List
This column contains only the list of signals and should not be confused with the actual pin name. For actual pin
names, see
For 5-V outputs, the left hand value represents slew rate control off, and the right hand value represents slew rate
control on. For 2.6-V outputs, the left hand value represents loads that are full drive, and the right hand value
represents loads that are half drive.
Care should be taken that neither a pull-up to greater than 3.1 V or an external output that can drive greater than
3.1 V is connected to this pin while the 2.6-V driver is enabled.
Pull-up/pull-down is active when pin is defined as an input and/or during reset, therefore, output enable is negated.
This also means that external pull-up/pull-down is NOT required unless specified.
For this 5-V output, a drive load of 200 pf is possible but with a rise/fall time of 300 ns.
During reset, the output enable to the pad driver is negated and the PD is active. After reset is negated, the PD is
disabled.
2.6-V outputs cannot be connected to a pull-up or driver greater than 3.1 V.
This pin requires a pull-up to 2.6 V if interrupts are ever enabled for this IRQ input.
This signal also includes the MDO5 function on the K27S mask set of the MPC561.
The MODCK[1:3] are shared functions with IRQ[5:7]. If IRQ[5:7] are used as interrupts, the interrupt source should
be removed during PORESET/TRST to insure the MODCK pins are in the correct state on the rising edge of
PORESET/TRST.
These pins are powered by KAPWR (keep-alive power supply). Any pull-ups on these pins should pull-up to
KAPWR.
KAPWR
VDDSYN
VSSSYN
ALTREF
NVDDL
QVDDL
VDDH
VDDA
VSSA
VDD
VRH
VSS
VRL
11
19
1
Appendix F, “Electrical
Voltage
≥2.6 V
2.6 V
2.6 V
2.6 V
2.6 V
2.6 V
2.6 V
0 V
5 V
5 V
0 V
5 V
5 V
0 V
Table 2-14. MPC561/MPC563 Signal Reset State (continued)
Controlled
Slew Rate
Option?
MPC561/MPC563 Reference Manual, Rev. 1.2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Characteristics.”
QADC64E Power Supplies
Drive
Load
(pF)
Global Power Supplies
USIU Power Supplies
—
—
—
—
—
—
—
—
—
—
—
—
—
—
2
Reset State
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Hysteresi
Enabled?
—
—
—
—
—
—
—
—
—
—
—
—
—
—
s
NVDDL
VDDH
VDDI
VSS
KAPWR
IRAMSTBY
QVDDL
VDDSYN
VSSSYN
VRH
VRL
ALTREF
VDDA
VSSA
Function After HRESET,
PORESET/TRST
Freescale Semiconductor