MPC562MZP56 Freescale Semiconductor, MPC562MZP56 Datasheet - Page 814

• Manufacturer Part Number: MPC562MZP56
• Description: IC MPU 32BIT 56MHZ PPC 388-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC562MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 64
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Processor Series: MPC5xx
• Core: PowerPC
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: SCI, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 22
• Operating Supply Voltage: 2.6 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 32 Channel)
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No

Peripheral Pin Multiplexing (PPM) Module
The PPM Module has two data transmit signals, PPM_TX[0:1], and two data receive signals,
PPM_RX[0:1]. The amount of data transferred on these signals depends on the setting in
PPMPCR[OP_16_8]. If the PPM is configured to transfer data in 16 PPM_TCLK cycles per 16-bit word
then all data in TX_DATA[0:15] is transmitted on the PPM_TX0 signal, and all data is received into
RX_SHIFTER[0:15] from PPM_RX0. If the PPM is configured to transfer data in eight PPM_TCLK
cycles per 16-bit word then the eight bits will transfer on each of the data transfer signals.
In SPI mode the phase and polarity of PPM_TCLK is selectable by programming bits in the PPMPCR
register. PPM_TCLK can have normal polarity (active high) or inverted polarity (active low). There are
two clock phases available: valid data can be latched on the transition of PPM_TCLK from its active edge
to inactive edge, or valid data can be latched on the transition of PPM_TCLK from its inactive edge to
active edge.
See
settings.
18-8
PPM_TCLK(1)
PPM_TCLK(2)
Section 18.4.2, “PPM Control Register
PPM_TCLK(1) = SYSCLK/4
PPM_TCLK(2) = SYSCLK/2
Update(1)
Update(2)
Update(3)
Update(4)
Update(1) every PPM_TCLK(1)clock
Update(2) every PPM_TCLK(2) clock
Update(3) every second PPM_TCLK(2) clock
Update(4) every fourth PPM_TCLK(2) clock
SYSCLK
SYSCLK
Care must be taken when setting the sample rate with respect to the
OP_16_8 bit setting. For example if the PPM is transferring data on an
8-clock cycle, then setting the sample rate to every 16 clocks will result in
lost data.
Figure 18-7. Examples Of Several TCLK Frequencies and Sample Rates
MPC561/MPC563 Reference Manual, Rev. 1.2
(PPMPCR)” for more information on SPI mode PPM_TCLK
NOTE
Freescale Semiconductor