ATMEGA88A-MMH Atmel, ATMEGA88A-MMH Datasheet - Page 162

• Manufacturer Part Number: ATMEGA88A-MMH
• Description: IC MCU AVR 8K FLASH 28QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA88A-MMH

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.11.2
8271C–AVR–08/10
TCCR2B – Timer/Counter Control Register B
• Bit 7 – FOC2A: Force Output Compare A
The FOC2A bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to zero when
TCCR2B is written when operating in PWM mode. When writing a logical one to the FOC2A bit,
an immediate Compare Match is forced on the Waveform Generation unit. The OC2A output is
changed according to its COM2A1:0 bits setting. Note that the FOC2A bit is implemented as a
strobe. Therefore it is the value present in the COM2A1:0 bits that determines the effect of the
forced compare.
A FOC2A strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR2A as TOP.
The FOC2A bit is always read as zero.
• Bit 6 – FOC2B: Force Output Compare B
The FOC2B bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to zero when
TCCR2B is written when operating in PWM mode. When writing a logical one to the FOC2B bit,
an immediate Compare Match is forced on the Waveform Generation unit. The OC2B output is
changed according to its COM2B1:0 bits setting. Note that the FOC2B bit is implemented as a
strobe. Therefore it is the value present in the COM2B1:0 bits that determines the effect of the
forced compare.
A FOC2B strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR2B as TOP.
The FOC2B bit is always read as zero.
• Bits 5:4 – Reserved
These bits are reserved bits in the ATmega48A/48PA/88A/88PA/168A/168PA/328/328P and will
always read as zero.
• Bit 3 – WGM22: Waveform Generation Mode
See the description in the
• Bit 2:0 – CS22:0: Clock Select
The three Clock Select bits select the clock source to be used by the Timer/Counter, see
17-9 on page
ATmega48A/48PA/88A/88PA/168A/168PA/328/328
Bit
(0xB1)
Read/Write
Initial Value
163.
FOC2A
W
7
0
FOC2B
”TCCR2A – Timer/Counter Control Register A” on page
W
6
0
R
5
–
0
R
4
–
0
WGM22
R
3
0
CS22
R
2
0
CS21
R/W
1
0
CS20
R/W
0
0
159.
TCCR2B
Table
162