ATMEGA16U2-MU Atmel, ATMEGA16U2-MU Datasheet - Page 192

• Manufacturer Part Number: ATMEGA16U2-MU
• Description: MCU AVR 16K FLASH USB 32-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16U2-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Core: AVR8
• Processor Series: ATMEGA16x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 16 MHz
• Data Ram Size: 1.25 KB
• Data Rom Size: 512 B
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Mounting Style: SMD/SMT
• Height: 0.95 mm
• Interface Type: SPI, UART
• Length: 5 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 5 mm
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

20.5.3
20.6
7799D–AVR–11/10
Memory management
Freeze clock
EPEN=1
ALLOC=1
The firmware has the ability to freeze the clock of USB controller by setting the FRZCLK bit, and
thereby reduce the power consumption. When FRZCLK is set, it is still possible to access to the
following registers:
When FRZCLK is set, only the asynchronous interrupt may be triggered:
The controller does only support the following memory allocation management.
The reservation of an Endpoint can only be made in the increasing order (Endpoint 0 to the last
Endpoint). The firmware shall thus configure them in the same order.
The reservation of an Endpoint k
cates the memory and insert it between the Endpoints k
“slides” up and its data is lost. Note that the k
Clearing an Endpoint enable (EPEN) does not clear either its ALLOC bit, or its configuration
(EPSIZE/PSIZE, EPBK/PBK). To free its memory, the firmware should clear ALLOC. Then, the
k
does not slide.
The following figure illustrates the allocation and reorganization of the USB memory in a typical
example:
Table 20-1.
i+1
Free memory
• USBCON
• DPRAM direct access registers (DPADD7:0, UEDATX)
• UDCON
• UDINT
• UDIEN
• WAKEUPI
Endpoints
activation
Endpoint memory automatically slides down. Note that the k
4
3
2
1
0
Allocation and reorganization USB memory flow
Endpoint Disable
Free memory
(ALLOC=1)
EPEN=0
4
3
1
0
i
is done when its ALLOC bit is set. Then, the hardware allo-
i+2
Free its memory
Free memory
Lost memory
(ALLOC=0)
and upper Endpoint memory does not slide.
ATmega8U2/16U2/32U2
4
3
1
0
i-1
and k
i+2
i+1
and upper Endpoint memory
. The k
2 (bigger size)
Free memory
Activatation
Endpoint
3
1
0
4
i+1
Endpoint memory
Conflict
192